Trudian TD-10MWK Smart Access Control Terminal User Guide
- June 13, 2024
- Trudian
Table of Contents
- Product Overview
- Controller Interface Description
- System Wiring References
- Wiegand Reader Installation Diagram
- Multi-door Control Function Description
- Multi-door Control Configuration
- Remote Control Controller
- FCC Caution
- Customer Support
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Trudian TD-10MWK Smart Access Control Terminal
Product Overview
Parameter
| Input | DC12V±10% |
|---|---|
| Swipe distance | 0~4CM |
| Working current | 200MA |
| Card reading type | IC card |
| Working mode | TCP/IP networking/offline |
| issuing mode | management platform card issuing |
| Working temperature | -20℃~70℃ |
| Relative humidity | 20% ~ 93% |
| Open mode | swipe card, APP, remote, password (optional) |
| size | control box:273 232 67mm |
reading head :86 86 8MM
Installation method| Control box: hanging installation reading head : 86 box
embedded installation.86 box requires a depth of 50MM inside
Controller Interface Description
Interface description:
| Location | Function Description |
|---|---|
| J4 | Power and relay output interface |
| J5 | Exit button and door magnetic detection interface |
| J6 | 485 bus communication interface |
| J1 | LAN cable crystal head interface |
| SW1(0 means no dialing, 1 means dialing to ON) | Mode selection( 00：TCP/IP LAN |
networking,01:Offline)
Interface Name| Function Description
---|---
+12V| Power and relay output interface
GND| Exit button and door magnetic detection interface
NC| 485 bus communication interface
COM| LAN cable crystal head interface
NO| Relays normally open
EXIT| Exit key signal detection
DSW| Door magnet signal detection
485A/B| 485 bus A/B interface
System Wiring References
Wiegand Reader Installation Diagram
(a) Connect the signal line in the back of the read head device as shown in
the figure below.
(b) Install the reading head device into the 86 box, (note that you need to
use the embedded wall inside the depth of 50MM style 86 box), lock the screws
to fix, as shown in the figure below.
(c) Read the head panel and read the head body snap together, first from the
upper snap down and then press the lower and bottom screw hole alignment;
finally in the bottom of the anti-theft screw hole screwed on the countersunk
head machine wire within the plum security screws fixed, as shown in the
figure below.
Multi-door Control Function Description
Operating mode selection
| Switch Setting | Indicates | Switch Setting | Indicates |
|---|
01
| Offline working|
00
| TCP/IP LAN networking
Startup status
TCP/IP LAN networking : When the power is on, the blue LED flashes, indicating
that it is looking for the network. When normally connected to the network,
the buzzer “tick ~ tick” two short beeps, the LED red light is always on,
indicating that the cloud access control has started normally; when 20 seconds
later is not normally connected to the network, the buzzer “tick tick tick”
three beeps, the LED red light is always on, indicating Connection network
failure, the controller forced to start. After the controller is normally
connected to the network, the LED green light will flash once every 20
seconds, indicating that there is data and the cloud platform interactive
communication.
Offline working : When the power is started, the buzzer “beep” a short
beep, the LED red light is always on, indicating that the cloud access control
has started normally.
Unlock status
When the lock is opened legally, the buzzer of the controller and the reading head will be “beep” at the same time, accompanied by a green LED flashing once, and the corresponding relay will be jumped, which means that the lock is opened successfully; when the lock is opened illegally, the buzzer of the controller and the reading head will be “beep beep beep” three times at the same time, accompanied by a red LED flashing three times, which means that the lock is opened and failed.
Unlock method
The device can be unlocked by swipe card, remote APP, out door button, management center platform remote, cloud server platform remote, password (optional), and many other ways.
Multi-door Control Configuration
Management Center Add Controller
Connect the controller to the PC with a network cable, open the controller
management software, and click Add Controller by Search. At this time, the
management software can automatically search for the multi-door controllers
connected to the LAN and assign them to the corresponding IP. Then configure
the controller to the corresponding area. Click to confirm that the controller
can be bound to the corresponding regional access control.
Add user and configure his permissions
In the management center, add users to configure the rights of the corresponding area controllers for them. After the configuration is completed, users can open the door in the room where these controllers are installed by swipe card, APP, password, etc. More detailed controller management and
Add User:
Configuration Permissions:
Remote Control Controller
Remotely open doors and view access records
After you open Trudian APP and log in the user you have added in the management center, the APP home page shows all the controllers that the current user can control. You can open the door remotely in APP, and you can also view all the door opening information recorded by the controller in APP.
View access records with APP：
Open the door remotely with APP：
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Customer Support
HQ Add: Farbell Technology Park,Yixian Road, Nanlang,
Cuiheng New District, Zhongshan City, Guangdong Province,
China. Zip Code:528451
Phone: +86 0760 – 23689666
E-mail: sales@trudian.com
If the problem is not solved properly,please send the mail to:
support@trudian.com
www.trudian.com/en/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>