Wipro Vesta 1380 Watt Cordless Steam Iron User Manual
- June 12, 2024
- Wipro
Table of Contents
Wipro Vesta 1380 Watt Cordless Steam Iron
PARTS IDENTIFICATION
HOW TO USE
HOW TO AVOID WATER LEAKAGE WHILE USING STEAM IRON BY FILLING WATER IN THE RIGHT MANNER
Make sure the iron is turned off and the power cord is unplugged from the electrical outlet.
- Set the ‘Variable’ steam knob to the ‘ ‘ Dry position before filling the iron with water.
- Open the ‘Water Fill’ and fill the Tank up to the ‘MAX’ Line on the tank.
- The water level can be observed through the transparent part of the tank, when the iron is placed vertically. In case the water level comes to low, refill the tank and follow the procedure described in steps 1 to 2 above.
- Pour out the remaining water after use.
NOTE: Most tap water can be used in this iron. Do not use water additives or substitute water such as linen or scented water in the steam iron, they can stain fabrics or damage the iron. Do not fill the water more than the ‘MAX’ position.
USING AS A DRY IRON
The set can be used as dry iron, even if there is water in the reservoir. Do Not put water in the reservoir when the set is used as dry iron for MANY HOURS.
- Unwrap the cord, Plug Power Base on.
- Adjust the dial so that the material to be ironed is set to the dial mark.
- Set the iron on Power Base and the pilot lamp will illuminate,
- When the pilot lamp goes out, it indicated that the iron has reached the required temperature.
- If you are not using the iron, even for a moment, you should replace it on the Power Base to avoid the damage to the soleplate.
- When iron is not hot enough, set the iron on Power Base again, The iron will heat up to the preset temperature and the pilot lamp will be illuminated.
HOW TO USE AS STEAM IRON
Fill the iron as described in ‘How to fill with water’.
- Unwrap the cord. Plug Power Base on.
- Filling iron with water.
- Set the iron on Power Base and the pilot lamp will be illuminated.
- Set the Temperature Control Dial to the Dry Mode position during heating process and the iron is ready to use when the indicator light goes out. Steam Ironing is only possible when at higher temperature settings indicated with ‘MAX’ mark; or else the water will leak from the soleplate.
- Turn the Temperature regulating knob to the required setting for different types of fabric.
- After the iron reaches the correct temperature, remove iron from the base and turn the regulator to steam iron mode and iron it for 15 to 20 seconds.
- After every use turn the steam regulator to dry mode and iron it for 45 seconds or until the indicator light gets on.
- When the indicator lights turns on, set the iron on Power Base again. The iron will heat up to the preset temperature and the indicator light will be illuminated.
HOW TO USE THE BURST OF STEAM
The burst of steam feature provides additional steam for removing stubborn wrinkles. It may be used with steam or dry ironing. Press the Power Steam button to release the surge of steam. Pressing the button several times may be necessary to prime the surge system. Wait a few seconds for the steam to penetrate the fabric before pressing the button again for more steam.
NOTE: For optimum steam quality, do not apply more than three successive shots after the indicator light goes off.
Precautions
AFTER EACH USE
- Turn the iron off and unolug.
- Empty the iron immediately after using. Do not store the iron with water in it.
- Wait until the iron has cooled before storing it, and always store it carefully to protect the soleplate from scratches, corrosion or stains.
- After letting iron cool down completely, store the iron vertically in a safe place.
OUTSIDE SURFACE OF THE IRON
- After unplugging and cooling the iron, simply wipe off with a damp cloth and if necessary, use a mild detergent.
- NEVER USE ANY HARSH CLEANERS.
SOLEPLATE
Starch and other residue may be easily removed from the soleplate with a damp cloth. To avoid scratches, never use a metallic pad to clean the Solelate, and never place the iron on a rough surface. If synthetics are ironed at a high temperature not only is the fabric usually ruined, but the iron Soleplate is often covered with the melted remains of the synthetic fabric. The best way to remove synthetic fabric residue from the Soleolate is to heat the iron and to iron over an old cotton rag.
NOTE: Never Use steam iron cleaners in the iron, since they may damage the working parts of the iron.
MAINTENANCE & SELF CLEANING
DO’S & DONT’S
_ IMPORTANT: _Your iron will give the best ironing results and will last longer if you Self Clean once a month, or more depending upon the usage.
- Filling the water tank up to half with water.
- Position the iron on its rear heel.
- Select the temperature control dial to ‘MAX’.
- Plug the iron.
- Allow the iron to heat up until the indicator light goes out.
- Unplug the iron from the electrical outlet.
- Keep the iron horizontally over the sink.
- Press down on the ‘Self Clean’ button for a longer period of time. Boiling water and steam will now emit from the holes in the soleplate.
- Move the iron forwards and backwards white this happens; let steam and water escape until the water tank is virtually empty.
- Release the ‘Self Clean’ button.
- Plug in the iron
- Set the temperature dial to the ‘MAX’ position, let the iron heat up again, the remainder of the water inside the steam chamber will now vaporize and leave the iron through the soleplate.
- During this process of dry steaming, it is advised to use it over and old piece of cloth.
INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
- Use the iron for its intended purpose; ironing fabrics on board.
- To protect against burns or injury to a person, do not iron or steam fabrics while being worn on the body.
- The iron should always be turned ‘OFF’ before plugging or unplugging from the outlet. Never pull the cord to disconnect from outlet, instead, grasp the plug and pull to disconnect.
- Do not allow cord to touch hot surfaces. Allow the iron to cool completely before storing.
- Always disconnect the iron from electrical outlet for filling or emptying water and when not in use.
- To avoid risk of electric shock, do not operate iron with a damaged cord or if the iron has been dropped or damaged.
- Close supervision is necessary for this appliance being used by or near children. Do not leave iron unattended while connected or on an ironing board.
- Burns can occur from touching hot metal parts, hot water, or steam. Hot water may leak from the iron. Use caution when filling or turning the steam iron upside down.
- To protect against burns or injury, do not direct steam toward the body when ironing.
- The iron must be used and rested on a stable surface. When placing the iron on its stand, ensure that the surface on which the stand is placed is stable.
More Information
- For repair, please contact Wipro Vesta Customer Care on 1800-425-1969
- For more information please visit Wipro Smart light: www.wiproconsumerlighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>