HOLLYLAND C1 Pro Hub8S Full Duplex Wireless Noise Cancelling Intercom System User Manual
- June 12, 2024
- HOLLYLAND
Table of Contents
Hollyland Solidcom C1 Pro – Hub8S
Hollyland Solidcom C1 Pro – Hub8S
User Manual
V1.0.0
Introduction
Thank you for purchasing Hollyland Solidcom C1 Pro full-duplex wireless
noisecancelling intercom system.
The Solidcom C1 Pro – Hub8S is a full-duplex wireless noise-cancelling
intercom system engineered to provide clear audio and all-day wearing comfort
in a truly wireless design with no beltpack required. The system operates in
the 1.9GHz band, providing a reliable LOS range of up to 1,100ft (350m).
This User Manual will help you through the installation and use of the
equipment.
Packing List
Solidcom C1 Pro – Hub8S Intercom Headset Package
| 1. Hub | x1 |
|---|---|
| 2. Remote Headset (With Blue Nameplate) | x8 |
| 3. 0B10 Wired Headset (With Red Nameplate) | x1 |
| 4. 8-Slot Charging Case | x1 |
| 5. Headset Batter | x16 |
| 6. Microphone Cushion | x9 |
| 7. 12V/2A DC Adapter | x2 |
| 8. Over-ear Leather Cushion | x9 |
| 9. On-ear Foam Cushion | x9 |
| 10. USB-A to USB-C Cable | x1 |
| 11. High-Gain Antenna | x4 |
| 12. Storage Case | x1 |
| 13. User Manual | x4 |
| 14. Warranty Card | x1 |
Note: The quantity of the items depends on the product configuration.
Quick Guide
Installing the Hub Antennas
Powering on the Hub
-
Connect the 12V/2A DC adapter to the hub.
-
Switch on the Hub.
Note: The hub can also be powered on by NP-F batteries, V-mount
batteries, or G-mount batteries.
Pairing
The hub and remote headsets that come from the same system will pair with each
other automatically right out of the box. Manual pairing is only required when
a new headset needs to be added or when a headset or the hub needs to be
replaced.
Connecting a Headset to the Hub Using a USB-C Cable
A USB-C cable is required for pairing. Connect the headset to the hub via the
USB interface on the hub and the USB-C interface on the headset. Then, the
number selection interface will automatically be displayed on the hub. Simply
press the arrow buttons to select a number and press the round
Menu/Confirmation button to complete number settings and pairing.
Setting
Headset Numbers on the Hub
When repairing and numbering a headset, be sure to turn on all the headsets to
avoid selecting duplicate numbers. Otherwise, the other headsets may not be
connected.
In case of wrong numbering for the headset, simply connect it to the hub using
a USB cable and perform pairing and numbering again.
Configuring the Hub on the Web Server
Turn on the hub, connect it to a computer using a network cable via the RJ45
interface on the hub and the network port on the computer, configure the same
network segment for the computer and hub, open a browser on the computer, and
then enter the following addresses (Check the corresponding addresses through
the network menu on the hub):
Default IP address of a master hub: 192.168.218.10
Default IP address of a remote hub: 192.168.218.11
You can log in to the web server (default password: 12345678) to upgrade
the hub, perform headset grouping, and set headset states.
Parameters
| Hub| Wired Headset
---|---|---
Interface| RJ45 interface Power interface (DC interface) 4-wire audio
interface (RJ45 socket)
USB interface 2-wire audio interface PGM audio interface USB-C interface 0B10
headset interface RF antenna interface| USB-C interface
Antenna| External| Built-in
Power Supply| DC power, NP-F battery, V-mount battery, G-mount battery|
** 700mAh lithium polymer battery
Operation Time| /| About 10 hours
Charging Time| /| About 2.5 hours
Volume Adjustment| Adjustment knob| Adjustable in 7 gears
Power Consumption| <4.5W| <0.3W
Dimensions| (LxWxH): 259.9mmx180.5mmx65.5mm (10.2”x7.1”x2.6”)| (LxWxH):
186.9mmx75. 6mmx188.6mm (7.4”x3”x7.4”)
Net Weight| About 1300g (45.9oz) with the antennas excluded| About 170g (6oz)
with the battery included
Transmission Range| 1,100ft (350m) LOS
Frequency Band| 1.9 GHz (DECT)
Wireless Technology| Adaptive Frequency Hopping
Modulation Mode| GFSK
Wireless Power| ≤ 21dBm (125.9mW)
Bandwidth| 1.728MHz
RX Sensitivity| <–90dBm
Frequency Response| 150Hz–7kHz
Signal-to-Noise Ratio| >55dB
Distortion| <1%
Input SPL| >115dBSPL
Temperature Range| 0℃ to 45℃ (working condition) –10℃ to 60℃ (storage
condition)
Note:** The highest working temperature is 40℃ when the adapter is used for
the power supply.
Safety Precautions
Do not place the product near or inside heating devices (including but not
limited to microwave ovens, induction cookers, electric ovens, electric
heaters, pressure cookers, water heaters, and gas stoves) to prevent the
battery from overheating and exploding.
Do not use non-original charging cases, cables, and batteries with the
product. The use of non-original accessories may cause electric shock, fire,
explosion, or other dangers.
Support
If you encounter any problems in using the product or need any help, please contact Hollyland Support Team via the following ways:
| Hollyland User Group
---|---
| HollylandTech
| HollylandTech
| HollylandTech
| support@hollyland-tech.com
| www.hollyland-tech.com
Statement
All copyrights belong to Shenzhen Hollyland Technology Co., Ltd. Without the
written approval of Shenzhen Hollyland Technology Co., Ltd., no organization
or individual may copy or reproduce part or all of any written or illustrative
content and disseminate it in any form.
Trademark Statement
All the trademarks are owned by Shenzhen Hollyland Technology Co., Ltd.
Note:
Due to product version upgrades or other reasons, this User Manual will be
updated from time to time. Unless otherwise agreed, this document is provided
as a guide for use only. All representations, information, and recommendations
in this document do not constitute warranties of any kind, express, or
implied.
FCC Requirement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the device. This
device complies with Part 15 of the FCC Rules.
Operations are subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operations.
FCC Radiation Exposure Statement :
The device has been tested and complies with FCC SAR limits.
Note:
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses, and can radiate radio
frequency energy, and if it is not installed and used in accordance with the
instrustions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful interference to
radio or television reception, which can be determined by turning the device
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the device and the receiver.
- Connect the device to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>