SW-MOTECH BC.HTA.18.682.21000 Legend Gear Side Bag System Instruction Manual
- June 4, 2024
- SW-MOTECH
Table of Contents
ANBAUANLEITUNG mounting instructions
BC.HTA.18.682.21000 **beinhaltet
HTA.18.682.11700 **HTA.18.682.11100
BC.HTA.00.682.11100 BC.HTA.00.682.11000
BC.LOC.00.682.10000/S
**MOUNTING INSTRUCTIONS
**
– READ AND SAVE THESE MOUNTING INSTRUCTIONS
Revision:01 – Datum / Date: 10-2021
SLH side carrier LH1 right / left
Thank you for choosing this premium product from SW-MOTECH. Please carefully
read and understand all instructions, safety messages, and warnings in this
mounting instruction prior to installation and use of this product to avoid
injury.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Visit our webshop for additional information, such as
application charts and PDF mounting instructions. Any other documents that may
be required (e.g. ABE certifications), are also available for download at our
webshop. Keep these mounting instructions as a reference.
SW-MOTECH assumes no liability for damage caused by improper installation
and/or maintenance work!
SAFETY ALERT SYMBOL
This safety alert symbol is used throughout these mounting instructions
to warn of the possibility of death, bodily injury or other warnings. The
words DANGER,
**WARNING and CAUTION are used with this safety alert symbol to convey
important safety messages and information related to the installation and use
of this product. These words along with the safety alert symbol mean:
DANGER: Indicates a hazardous situation that, if not avoided, will result
in death or serious injury!
WARNING: Indicates a hazardous situation that, if not avoided, could
result in death or serious injury!
CAUTION: Indicates a hazardous situation that, if not avoided, could
result in minor or moderate injury!
NOTICE: Important information, but not death or injury related (property
damage only]!
WARNING: The installation and/or maintenance of this product requires
advanced mechanical skills, the proper tools, and a thorough understanding of
tool use and torque specifications. For your own safety, SW-MOTECH recommends
having installation and/or maintenance carried out by a qualified and
certified motorcycle mechanic.
WARNING: Should you choose to self-install this product, carefully and
completely read all installation and safety instructions before installation
and use, and follow all the directions and safety precautions given in the
mounting instructions to avoid serious injury or death. Also, pay attention to
all relevant information in the vehicle manual during installation and use.
IF YOU DO NOT UNDERSTAND ANY PART OF THESE INSTRUCTIONS OR NEED CLARIFICATION
OF ANY INSTRUCTION, DO NOT ATTEMPT TO MOUNT THIS PRODUCT WITHOUT CONTACTING
SW-MOTECH FOR ASSISTANCE.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included.
****CAUTION: Make sure that your vehicle is parked safely and cannot fall
over. Turn off the engine and remove the ignition key. Let the engine/exhaust
cool off if necessary. Disconnect the vehicle battery when working on the
electrical system. Use appropriate tools and wear always safety glasses and
hand protection. Have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturer’s specifications or
replaced by parts and hardware delivered by SW-MOTECH.
WARNING: Secure all threads, unless otherwise specified, with a medium-
strong strength liquid thread locker. Torque specifications undefined by SW-
MOTECH must be obtained from the vehicle manufacturer or by a certified
motorcycle workshop!
FUNCTION CHECK: After installation also make sure that no moving parts
are obstructed, and the function of the vehicle is not hindered in any way.
Cables and hoses must not rub and/or be pinched.
WARNING:** Before starting to ride, perform a comprehensive check of all
functions. After the first 50 km and then at regular intervals, check the
tightening torque of all connections and the proper fit of the product.
Installed accessories can change the driving behavior/stability of the
vehicle.
PARTS LIST
Part| Anzahl
Quantity| N•nc
---|---|---
| SLH Side Carrier right
Side Carrier; right| 1 /1|
Countersunk Screw; inch thread; black| 2 n|
Stepped Spacer| 2 /2|
Flanged Spacer| 2 /2|
Spacer| 1 /1|
Countersunk Screw; black| 1 /1| 8
Plastic Plug| 1 /1|
Spacer; Schwarz| 2 /2|
SLH Side Carrier left| 1 /1|
Side Carrier; left
Mounting parts see SLH Side Carrier right
10.9| Regelgewinde / Coarse Thread 0| M4| M5| M6| M8| M10| M12
---|---|---|---|---|---|---|---
Stahl FK 10.9 / Steel CL 10.9 IN•rn| 4,1| 8,1| 14| 34| 67| 115
Note: All measurements in millimeters. b The second number indicates the total quantity of the part in the delivery. No torque specifications: Use the torque defined by the vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
MOUNTING
WARNING: Always wear eye and hand protection!
WARNING: Always use the appropriate tools!
Remove the shown screws from the vehicle.
WARNING: If factory-mounted reflectors are concealed by the side carrier,
the reflectors must be removed and/or attached elsewhere in the same mounting
position! It is essential to observe the country-specific regulations
regarding lighting equipment (reflectors)!
HINWEIS: If the side carrier (1} is to be mounted with the original
Holdfast Docking Hardware Kit {Orig.}, the spacers [4] are not required.
Attach the side carrier [1] with the parts of the spacers [8] shown in the
detailed drawing.
Attach the spacer [5] to the side carrier (1).
WARNING: Use a liquid thread locker!
Tighten the screw [6] as specified. Attach the side carrier (1) to the
vehicle.
WARNING: Use liquid thread locker!
Tighten the screws (2) with the manufacturer’s specified torque.
MOUNTING – READ AND SAVE THESE MOUNTING INSTRUCTIONS
PRODUCT SPECIFIC INFORMATION
NOTICE: Observe the country-specific regulations concerning vehicle registration/operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
‘ MOUNTING INSTRUCTIONS
Revision:00 – Datum / Date: 04-2021
Legend Gear side case LH1 / LH2
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application
charts and PDF mounting instructions. Any other documents that may be required
(e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behavior and/or
stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle
registration/operation as well as TUV regulations if applicable. If required,
register installed parts in the vehicle documents through an appropriate
inspection authority. PREPARATION: Read the mounting instructions carefully
and make sure that all items of the parts list are included. Make sure that
your vehicle is parked safely and cannot fall over. Turn off the engine and
remove the ignition key. Let the motor/exhaust cool off if necessary.
Disconnect the vehicle battery when working on the electrical system. Use
appropriate tools. Have another person to help you. FUNCTION CHECK: This is a
universal product. For this reason make sure BEFORE the first use, that the
product can be fixed properly and used without problems with your vehicle
type. After fixation also make sure that no moving
parts are obstructed and the function of the vehicle is not hindered in any
way. Lamps as taillight and turn signals must not be limited in their
function. Cables and hoses must not rub and/or be pinched. Before starting to
ride, perform a comprehensive check of all functions.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect motorcycle driving and
braking performance!
ATTENTION: Before riding and at each stop (every 200 km) check the proper
fixation of the product!
ATTENTION: The maximum load must not be exceeded! The maximum vehicle
load specified by the manufacturer must not be exceeded!
NOT FOR OFFROAD USE!
PARTS LIST&CARE
CARE
Clean the product periodically or after each trip, as dust and dirt have a
wear effect and permanent stains can be prevented. Clean the product after
riding in salty conditions, to avoid damage from salt.
First, remove dust and encrustations with a soft dry brush. Remove stubborn
deposits with a soft cloth and warm soapy water. Do NOT use strong cleaning
agents, rough cleaning tools or a high-pressure washer! Then rinse with clear
water.
Before re-use dry the product for at least 24 hours in the air (not in direct
sunlight).
FIXATION
Assemble the components as shown in the drawing.
Pay attention to the side-specific alignment of the bolt, as emphasized in the
schematic drawing. ATTENTION: Use liquid threat locker!
Tighten the screw as specified.
Loop the string as shown.
Hang the bag (1) into the sockets of the mounting bracket attached to your
vehicle.
Pay attention that both retaining elements are completely hooked into the
socket contours of the mounting bracket.
Secure the bag (1) with the quick turn fastener (3), by inserting it into the
opening and turning it clockwise.
Pay attention to the audible clicking sound.
The inserting position of the quick turn fastener differs depending on the
vehicle’s side.
Attach the string of the quick turn fastener to the loop on the inside of the
bag.
ATTENTION: Before each ride, lock the lid of the bag. Thoroughly clean the front of the lid from grease and dirt. Attach the reflector (4) to the lid as shown in the drawing.
MOUNTING INSTRUCTION
Art.-Nr. / Item No.: BC.LOC.00.682.10000/S – Revision:00 . 01-2019
Legend Gear lock set
Nr.
No.| Art.-Nr. / Bezeichnung
Item No. / Description| Anzahl
Quantity
---|---|---
(1)| | 2/2
(2)| | 2 /2
| Packed by; | Date of packaging |
|---|
Copyright by
SW-MOTECH GmbH & Co. KG Errors and omissions excepted. Technical and design
modifications are subject to change.
SW-MOTECH GmbH & Co. KG
Renewed 7-10
35282 Rauschenberg Germany
Tel. / phone + 49 (016425 / 8168 – 050 Fax / fax + 49 (016425 / 8168 – 10
infofasw-motech.com
www.sw-motech.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>