CLAGE Zip KXF 2.1 Fine Filter Instruction Manual

CLAGE Zip KXF 2.1 Fine Filter

Product Information

The Zip KXF 2.1 Feinfilter is a fine filter used for water filtration. It is designed to remove impurities and improve the taste and odor of water. The filter has a 0.2 Micron rating, which means it can effectively remove chlorine and particulate matter from the water.

Product Usage Instructions

Safety Instructions:

• Ensure that the filter is installed and used according to the manufacturer’s instructions.
• Do not use the filter with water that exceeds the maximum influent concentration values mentioned in the table below.
• If you experience any unpleasant taste or odor, replace the internal filter cartridge.

Replacing the Internal Filter Cartridge:

1. To remove the filter, twist it and pull it down gently.
2. Be cautious as a small amount of residual water may leak.
3. Unpack the replacement cartridge, write the current date on the label, and remove the hygiene cap.
4. Insert the new cartridge into the filter head and push it up.
5. Twist the cartridge a quarter turn to the right until it comes to a stop and locks into place.

Filter Specifications:

Substance| Influent Concentration| Average Maximum Concentration| Maximum Permissible Value| Average Reduction
---|---|---|---|---
Chlorine| 4 mg/L / 5 mg/L| 0.05 mg/L| 97.4%
Particulate Class I particles| 0.5 to| N/A| N/A| N/A

Note: Ensure that all John Guest pipe ends are clean and cut at  right angles.

Safety Instructions

• Designed for indoor use only.
• Do not install where exposed to direct sunlight or temperatures <4 °C or >40 °C.
• Minimum safe operating water pressure is 70 kPa, maximum 700 kPa.
• Do not install where water quality is unknown or microbiologically unsafe.
• After a period of non-use thoroughly flush the filter or tanks.
• For safety’s sake, replace all filter cartridges at intervals of 12 months or less.
• Replace any filter if water flow slows or if unpleasant tastes or odours occur.

WARNING
To reduce the risk associated with the ingestion of contaminants:

• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

CAUTION
To reduce the risk associated with property damage due to water leakage:

• Read and follow Use Instructions before installation and use of this system.
• Installation and use MUST comply with all state and local plumbing codes.
• Protect from freezing, remove filter cartridge when temperatures are expected to drop below 4.4°C.
• Do not install systems in areas where ambient temperatures may go above 43° C.
• Do not install on hot water supply lines. The maximum operating water temperature of this system is 38°C.
• Do not use a gas torch or other high temperature sources near system, cartridges, plastic fittings or plastic plumbing.
• Do not install in direct sunlight or outdoors.
• Ensure all tubing and fittings are secure and free of leaks.
• The disposable filter cartridge MUST be replaced every 12 months, at the rated capacity or sooner if a noticeable reduction in flow rate occurs.

Exchange of internal filter

FILTER CARTRIDGE REPLACEMENT

This instruction is for the replacement of the filter in the Zip HydroTap product where the filter is mounted internally. In preparation for your filter flushing, ensure you have a 10 litre container available.
Some water may drip from the filter head (socket) during replacement. Keep a towel handy to dry up any drips.

Change the Filter:

1. Go to filter flush in the menu, this isolates the water supply. Variations apply depending on the product. Refer to individual instruction.

2. Relieve system pressure via the filter flush stop cock, a quick open and close will do. Use the bucket to catch the discharge.

3. Grasp filter cartridge, rotate the cartridge a quarter turn to the left and gently pull down.
   Caution: a small amount of water will drip as the cartridge is removed.

4. Do not tilt the cartridge as water may spill from it if tilted.

5. Unpack replacement cartridge, write today’s date where shown on the label and remove the sanitary cap.

6. Avoid touching the filter O-rings and filter opening as this may cause bacterial contamination of the cartridge.

7. Push the new cartridge in and up into the filter head.

8. Turn the cartridge a quarter turn to the right until the cartridge comes to com-plete stop and is locked into position.

9. Locate the filter flush hose situated behind the filter cartridge and direct the hose into a container ready for flushing. Open the filter flush stop-cock. On the menu press Adjust or Start, this will start the water flow, flushing the cartridge. Allow at least 10 litres of water through the cartridge before use, to activate the filter. Isolate the filter flush stop-cock and re-fit behind the filter cartridge. Now stop filter flush or press filter flush off to stop the flow. (It may take approximately 3 minutes to flush the 10 litres.)

10. Wipe up any spills and dispose of spent filter cartridge and packaging thought-fully.

11. Close the door to secure the appliance.

12. Reset the internal filter counter of your HydroTap unit. Follow the instructions of the unit.

Inserting & Removing Water Supply Lines from John Guest Fittings

General instructions for John Guest connections
NOTE: Ensure all John Guest tube ends are cut clean and square.

Other information

More Information
When the filter is fitted to an appliance, please refer to the appliance owner’s guide for more product specific information and advice on how to avoid contamination from improper handling and installation.

Warranty
Zip Water Filter cartridges are not covered by standard Zip warranty as filter life may vary according to water quality and rate of use.

Filter Performance Data – 0.2 Micron

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF
This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentra- tion of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI Standard 42 and 53

This appliance meets the domestic water treatment appliance Standards AS/NZS 3497 and AS/NZS 4348 for the following water process

ü

II
II (a)| Microbiological Treatment
Bacteria Removal| Will remove or inactivate bacteria.| N/A
II (b)| Virus Removal| Will remove or inactivate virus.| N/A
II (c)| Protozoa Removal| Cryptosporidium and Giardia.
Will not remove or inactivate bacteria unless II(a) and II(b) are passed.| ü
III| Particulate Reduction| Reduces cloudiness.| ü
IV| Taste and Odour Reduction| Reduces tastes and odours.| ü
V| Chemical Treatment| Decreases certain chemicals:– Lead| ü

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi (0.7 – 6 bar), non-shock
• Temperature: 35 -100°F (2-38°C)

System Tested and Certified by NSF International against NSF
ANSI Standard 42 and 53 for the reduction of:
STANDARD NO.42 – STANDARD NO.53 – AESTHETIC EFFECTS            HEALTH EFFECTS
Bacteriostatic Effects             Chemical Reduction
Chemical Reduction                  Lead
Taste & Odor                         Mechanical Filtration
Chlorine                                   Cyst

Mechanical Filtration Nominal Particulate Class
The term “bacteriostatic” indicates that the system limits the pas- sage or growth of bacteria that may already exist in the incoming water. It does not mean that water leaving the system is safer to drink than water entering the system.

CLAGE GmbH
Pirolweg 4
21337 Lüneburg
Deutschland
Telefon: +49 4131 8901-0
E-Mail: service@clage.de
Internet: www.clage.de
All components are FDA CFA compliant
Subject to technical changes, design changes and errors.
9120-34435 11.22

References

• Global-Mark | Confidence with Commitment
• Startseite · Durchlauferhitzer, warmes Wasser und mehr! · CLAGE.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>