CLAGE FXS 3 Remote Control Kit for Instantaneous Water Heaters Instruction Manual

FXS 3 Remote Control Kit for Instantaneous Water Heaters
Instruction Manual

Operating and installation instructions

Remote control kit FXS 3 for instantaneous water heaters

Safety notes

**** This remote control may only be installed and started up for the first time by an authorized specialized company. Responsibility for compliance with the applicable standards and installation regulations rests entirely on the company installing the appliance. We cannot accept any liability for damage and losses due to non-compliance with these instructions. Read this manual completely before starting up the remote control.
The handling of the appliance and the remote control are equitable. The last set temperature will be used by the instantaneous water heater. Make sure not to set a high tempera-
Tue, inadvertently. We recommend activating the temperature limit function (see the manual of the instantaneous water heater).
Flat batteries can leak and damage the remote control. Hence, replace flat batteries right away as soon as the battery symbol lights up in the display or the remote control does not respond after a keystroke.
When the remote control is not to be used in the long term, remove the batteries.
Do not expose the remote control to moisture.
Keep the remote control and wall bracket away from credit cards or other cards with magnetic strips.
The built-in magnets can damage the card’s magnetic strip.
This appliance can be used by children aged 3 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be performed by children without supervision.

Description of appliance

The FXS 3 remote control set consists of the FX 3 remote control and the FXE 3 radio adapter. The FX 3 remote control allows a convenient operation of the instantaneous water heaters DFX Next, DEX Next, DEX Next S, DEX Next S Twin, DSX Touch, DSX Touch Twin, CEX, CFX and MCX even if the heater is installed under a sink or in a secondary room. An energy-efficient and adequate choice of the water temperature is furthermore possible under these conditions with the FX 3 remote control.
The communication between the remote control and the instantaneous water heater is via Bluetooth ® . Due to this technology, the data transfer is secured even under difficult installation conditions.
To connect the remote control to a DEX Next, CEX or MCX instantaneous water heater, the provided radio adapter must be installed.

Dimensions 

Technical Data

1. Do not use rechargeable batteries.

Installation

Figure 1:
Installation with adhesive tape

Figure 2:
Optional installation with dowels and screws
5.1 Mounting the wall bracket

• Before attaching the wall bracket to the wall, ensure that the remote control has radio contact to the instantaneous water heater from its designated position.
• The wall bracket of the remote control can either be attached securely with the included adhesive tape, after stripping off the protection film (as shown in fig. 1) on a plain surface (e.g. a tile) or with suitable dowels (Ø 4 mm) and screws (as shown in fig. 2).
• When using the adhesive tape it is not possible to adjust the position afterward because of the strong adherence of the glue. Therefore, pay attention to a horizontal alignment when attaching it.
• The remote control is magnetically retained at the wall bracket.

5.2 Mounting the radio adapter inside a DX
Attention!
Before assembling the transmission unit disconnect the water heater from the mains supply!

1. Remove the electronics cover, release the PCB from the catch and lift it slightly.
2. Connect the radio adapter, Pay attention to the proper position of the connector! The connector has to be fitted into the notch properly.
3. Snap the PCB back into place and attach the electronics cover.

The antenna is very fragile!
Figure 3:
Installation of transmission unit DX

5.3 Mounting the radio adapter inside a CX
Attention!
Before assembling the transmission unit disconnect the instantaneous water heater from the mains supply! Pay attention to the proper position of the connector! The connector is to be fitted to the notch properly.
The antenna is very fragile!
Figure 4:
Installation of transmission unit CX

5.4 Mounting the radio adapter inside an MX
** Attention!
Before assembling the transmission unit disconnect the instantaneous water heater from the main supply! Pay attention to the proper position of the connector! The connector has to be fitted into the notch properly.
The antenna is very fragile!
Figure 5:**
Installation of transmission unit MX

Initial operation

1. Make sure that the power supply to the instantaneous water heater is switched on (fuse) and that the display of the instantaneous  water heater (if available) shows
   the latest set value.

2. After inserting the batteries, the remote control briefly displays all symbols. Then “8A” and the percentage of battery charge are displayed and the display changes to the PIN entry “P1”.

3. Press – and + to change the current digit. Press to change to the next digit. After entering “P4” and pressing1, the PIN is applied.

4. DEX/DFX/DSX: Enter the first four digits of the Bluetooth PIN and confirm with 1. The PIN can be found on or at the type plate of your instantaneous water heater.
   CEX/CFX/MCX: Enter the last 4 digits of the serial number. The serial number can be found on the type plate of the instantaneous water heater and in the warranty booklet.

5. After entering the pin, the remote control automatically connects to the instantaneous water heater, and “d1” appears during the registration procedure. If there are several instantaneous water heaters within range, they may be checked first (display “d2… d3…”). This can take up to one minute. To avoid this, hold the radio remote control directly in front of the instantaneous water heater to be registered.

6. Once connected, the display of the remote control switches to the setpoint value display.

In the case of an unsuccessful registration, the display indicates “E1”. The remote control quits the registration process and switches to standby mode. By pressing a button the registration process will be repeated.
If the registration is impossible after a number of trials, check the pinning position of the radio adapter.
Notes:

• With no remote control registered or without a working radio connection, the instantaneous water heater heats to the prior selected set temperature.
• After replacing the batteries, a new registration is not required.
• After a power failure of the instantaneous water heater, a new registration is not required.
• Automatic re-registration after a battery change or power failure can take up to one minute.
• If the instantaneous water heater makes noises (beeping, buzzing) after switching on, a software update is being carried out. .

Re-registration

To connect the remote control to another instantaneous water heater, press and hold all four buttons on the remote control for at least 5 seconds.
This starts the initial operation mode.

Handling

The remote control is equipped with the following functions:

1. Temperature selection buttons
   You can set the required temperature gradually to a lower or higher value using the two buttons – and +.
   Notes: If the temperature display is set to “–” with a button, the instantaneous water heater switches off the heating function.
   If the maximum possible temperature limit is reached by the button, this is indicated by a short flashing of the temperature display.

2. Program buttons
   The two program buttons 1 and 2 allow to quickly select the preset temperature without the need to press the buttons several times.
   The factory setting for the program is 35 °C and for the program, it is 48 °C. You can assign your own settings for the program buttons:
   • Select the desired water temperature with and.
   • To save the current temperature, press the program button 1 or 2 for about two seconds.

3. Restart and battery capacity
   Press and hold keys 1 and 2 for approx.2 seconds to restart the remote control. All symbols are displayed briefly, followed by the battery display “8A”.

4. Info menu
   Press and hold the program keys  1 and 2 for about 5 seconds to open the info menu.
   Press or briefly to navigate back and forth in the displays. Long presses on 1 and 2 exit  the menu again.

Menu displays:

| Info menu indicator
---|---
Current battery capacity in percentage
Current error status
The temperature of water inlet in °C
The temperature of water outlet in °C
The highest selectable temperature in °C
Current water flow in l/min
Current power consumption in kW
Current power consumption in percentage
Maximum appliance power in kW
Calibration value
Signal strength in percentage
Software version digit 1
Software version digit 2
Software version digit 3
Digits 1 and 2 of the stored pin
Digits 3 and 4 of the stored pin

Displayed information

The representation corresponds to the temperature indication of the water heater display (if available) after a keystroke on the remote control. The description ofthe function can be found in the manual of the instantaneous water heater.
Radio communication
The radio symbol is displayed on the radio remote control as soon as it has been successfully registered with an instantaneous water heater.
Battery
If the batteries of the remote control are flat, the battery symbol is displayed. In this case, exchange the batteries (see chapter “Battery replacement”).

Energy saving mode ECO
The symbol ECO shows that the appliance works in an energy-saving mode, i.e. the momentary energy consumption is subject to the selected temperature and to the flow rate in the energy-saving mode.
Power limit MAX
If the full output of the instantaneous water heater does not suffice to heat the tapped quantity of water, this will be indicated by MAX on the FX 3 screen.
Operation with preheated water
If the cold water inlet temperature is higher than the set value of the hot water outlet, the instantaneous water heater will not heat. In this case, no power is emitted by the appliance, and the sun symbol is displayed on FX 3 screen.

Communication of the remote control

• The remote control contacts the instantaneous water heater in regular intervals. In case of a temperature change at the instantaneous water heater or water tapping without a previous key press on the remote control, the updated information on the display of the remote control may be shown with a slight delay.
• Without a working radio connection, the appliance heats to the prior selected set value.

Troubleshooting and service

The following table will help you to determine and rectify the reasons for possible problems.

remove and insert the batteries again
Transmission range exceeded| Place the remote control closer to the appliance, press the button
Display: “d r| Registration in process| Hold the remote control in front of the instantaneous water heater
Symbol “battery” lights| Flat batteries| Insert two new types of AAA-batteries
Temperature changes unintentional| Operation via other remote control, Smart Control app, or directly on the water heater| Only register the desired remote control
Display: “E2”| The PIN was entered incorrectly several times| Wait a few minutes and perform re-registration (see chapter 7), enter the correct PIN
Display: “ES”| Connection error| If this happens repeatedly, replace the batteries, contact customer service

Trouble-shooting and service

If you cannot rectify the fault with the aid of this table, please contact:
CLAGE GmbH
After-Sales Service
Pirolweg 4
21337 Lüneburg
Germany
Phone: +49 4131 8901-400
Email: service@clage.de
We can either give you the name and address of an authorized customer service company or repair the heater ourselves. In the latter case, please send in the heater (at your cost and risk) with details of the problem and a copy of the sales invoice.

Battery replacement

Replace the batteries with new AAA batteries when the battery symbol flashes up.

• Do not use rechargeable batteries!
• Non-rechargeable batteries are not to be recharged.
• Different types of batteries or new and used batteries are not to be mixed.
• When replacing the batteries, observe the correct polarity.

Disposal
Batteries may contain environmentally hazardous substances.
Therefore, used batteries must be disposed of at special collecting points and not be mixed with general household waste.
At the end of the remote control’s lifetime, the batteries must be disposed of separately from the appliance.

Environment and recycling

Disposal of transport and packaging material:
For smooth transport, your product is carefully packed. The disposal of the transport material is carried out by the specialist tradesman or the specialist trade. Separate the sales packaging according to materials separated according to materials via one of the dual systems in Germany.
Disposal of old products: Your product was manufactured from high- quality, reusable materials and components. Products marked with the crossed- out wheeled bin symbol must be disposed of separately from household waste at the end of their service life. Therefore, take this product to us as the manufacturer or to one of the municipal collection points that recycle used electronic devices. This proper disposal serves to protect the environment and prevents possible harmful effects on humans and the environment that could result from improper handling of the products at the end of their service life. For more detailed information on disposal, please contact your nearest collection point or recycling center or your local council.
Business customers: If you wish to discard equipment, please contact your dealer or supplier for further information.
For disposal outside Germany, please also observe the local regulations and laws.

CLAGE GmbH
Pirolweg 4
21337 Lüneburg
Deutschland
Telefon: +49 4131 8901-0
E-Mail: service@clage.de
Internet: www.clage.de 

 Subject to technical changes, design changes, and errors. 9120-25722 07.22

References

• Startseite · Durchlauferhitzer, warmes Wasser und mehr! · CLAGE.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>