heatit 250W ZIG Dim Rotary Dimmer User Guide

heatit 250W ZIG Dim Rotary Dimmer

Product Information

• Product Name: HEATIT MOUNTING A ZIG DIM 250W
• Article Number: 14 444 20
• Document Version: 2023-A
• Document Date: 01.06.2023

Introduction

The HEATIT Zig Dim is a Zigbee rotary dimmer designed for various types of light fixtures. It works well with most low loads, including LED lights, without causing flickering.LED. The dimmer is equipped with an external momentary switch option. This allows you to dim and turn on/off the light. The dimmer fi ts in European wall boxes and can be used with most frames that are adapted to System 55. When connecting low loads it is recommended to use a bypass. The dimmer also features an external momentary switch option, allowing you to dim and turn on/off the light. It fits in European wall boxes and can be used with frames adapted to System 55.

Note : Dimming may be challenging, so it is recommended to check the compatibility of different light sources before installation.

Installation

Installation must be done by a  qualified electrician in accordance with national building codes. Before installation, disconnect the power to the device from the mains. During installation, power to the device must be disconnected at all times.

MOUNTING

WIRING DIAGRAM

• Max tightening torque terminal screws: 2Nm.

Installation and Wiring:

1. Switch off the mains voltage (turn off the fuse).

2. Open the junction box.

3. Connect according to the wiring diagram as shown above:

   • Connect the Live to the dimmer terminal marked ”L”.
   • Connect the load terminal marked ”L” to the dimmer terminal marked

4. Install the dimmer (A) in the wall box. Make sure that no wires are pinched.

5. Attach the cover (B) with the supplied nut (C).

6. Attach the button (D) with a simple push.

7. After verifying the connections, switch on the mains voltage.

8. Set the primary controller in add mode.

9. Press the reset button on the dimmer 3 times in a rapid sequence. The HEATIT Zig Dim is now included in your network.

Add/Remove

The primary controller/gateway has a mode for adding or removing devices. Please refer to your primary controller manual on how to set the primary controller in add/remove mode. The device may only be added or removed from the network if the primary controller is in add/remove mode.

Inclusion to a Zigbee network

1. Remove the device from any previous Zigbee network that it may have been added to, otherwise, pairing mode will fail.
2. Set the primary controller to add mode.
3. To start the confi guration process, press the Reset button or the external switch connected to P, 3 times in rapid succession.
4. The device LED will blink in green when the adding procedure has been successfully initiated.

Removing from Zigbee Network:
Removing a device from the Zigbee Network is initiated from the gateway. Check your gateway manual on how to remove a device.

Performing a Factory Reset:

To perform a factory reset:

1. Press and hold the Reset button.
2. After 3 seconds, the LED will start to blink green.
3. After 20 seconds, the LED will stop blinking and emit a constant light.
4. You may now release the button.

Figure 1 (Success)

Within the 3-second period,  the button must be released. If the button is released within this period, the device will reset and start blinking red because it is not included in a gateway.

Figure 2 (Fail)

If the button is released before the 3-second period, the device will indicate fail by turning the RED LED on for 3 seconds.

Figure 3 (fail)

The button MUST be released between 20 and 23 seconds for local reset to take place. If held longer, the device will ignore the command.

TOUCHLINE

1. Press the reset button 4 times.
2. The device LED will blink blue when it is ready to be paired.
3. Bring the remote within 10 cm of the dimmer and set the remote to TouchLink pairing.
4. If the procedure was successful, the LED will light up in solid green for 3 seconds.

Note:

• When neither device (dimmer and remote) are included in a Zigbee network, each dimmer can only link to one remote.
• When both devices are included in the same Zigbee network, each dimmer can link with max. 30 remotes.
• For Philips Hue Hubs and Amazon Echo Plus, add remote and device to network first, then TouchLink.

FIND AND BIND

1. Press the reset button 5 times.
2. The device LED will blink yellow when it is ready to be added.
3. Set the remote into Find and Bind mode and enable Find and Bind pairing. Please refer to the manufacturer’s instructions on how to do this.
4. There should be an indication on the remote that it has successfully connected to the dimmer, and can control it.

CONTROLS

MEASUREMENTS AND DRAWINGS

FEATURES

• Zigbee rotary dimmer
• 2-wire
• 5W – 250W LED
• Rotary and push dimming
• Nemko certifi ed
• Trailing edge
• Overload protection
• Short circuit protection
• Surge protection
• Overheat protection
• External momentary switch
• Min. dim level adjustable
• Max dim level auto-calibration

TECHNICAL DATA

• Protocol:  Zigbee, 2.4GHz
• Chip : Zigbee 3.0
• Rated voltage: 230VAC 50Hz
• Power: 5W – 250W
• Controls: Rotary and push dimming
• Ambient temperature: 5°C to 40°C
• Storage temperature: 5°C to 40°C
• Range RF: Min. 40 meter
• Flush mounting depth: 24mm
• Screw terminals: Max. 2.5mm² 2Nm
• IP Code: IP21
• Size (LxWxH): 84 x 84 x 43mm
• Approvals: CE, Nemko

Working frequency 2.4GHz, Max output power 19,8dBm. The distance between user and products should be no less than 20 cm.

MAINTENANCE

The device is maintenance-free. Indoor use only

We have designed this product in accordance with our strict quality requirements (ISO 9001) and environmental requirements (ISO 14001). All electrical installations must be carried out by an authorized electrical installer. The product must be installed in accordance with our installers manual and national building codes.

Any wrongful installation, misuse or damage to the product, is not covered under warranty.

Heatit Controls AB can not be held liable for any type of errors or omittances in our product information. Product specifications may change without further notice.

Org. doc. 01.06.2023

Heatit Controls AB l Läkarvägen 4, 454 31 BRASTAD, SWEDEN

• Phone: +47 61 18 77 77
• post@heatit.com 
• www.heatit.com

1444420_Quick Guide_Heatit Zig Dim 250W.indd 6

22.05.2023 12:49:58

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>