Futaba 1M23N25701 S.BUS Encoder SBE-1 Instruction Manual
- June 12, 2024
- Futaba
Table of Contents
Futaba 1M23N25701 S.BUS Encoder SBE-1
SBE-1 S.BUS Encoder****
**
**
Note : Always read this manual before using the SBE-1. Store this manual where it can be used at any time.
Product Information
That you for purchasing an SBE-1 S.BUS*1 encoder. The SBE-1 is a converter that is used when using a CGY750 gyro or other exclusive S-BUS receiver device with a receiver for conventional system use. It allows the signals (PWM) of a conventional system of up to 10 channels to be converted to S.BUS system signals.S.BUS is the standard name of Futaba serial communication for R/C systems.
Precautions
WARNING: Take the same protective measures against vibration, shock, high temperature, and the invasion of moisture with the SBE-1 as you do with the receiver.
- Precision parts are used in the SBE-1. In addition, it is not constructed to prevent the invasion of moisture. There is the danger of a crash due to abnormal operation.
CAUTION: Do not connect anything other than an S-BUS device to the S.BUS output. Futaba Corp. will not be responsible for damages caused by combination with other than Futaba Corp. products.
- There is the danger of abnormal operation and damage.
Futaba Corp will not be responsible for damages, etc. caused by combination with other than Futaba Corp. products.
Name of Each Part and Connection Method
To conventional system receiver (up to 10chs):
- LED (green): Connects to the S.BUS input connector of an S.BUS device.
To S-BUS device:
- Connects all the connectors corresponding to the channel necessary to operate the S.BUS device.
- Always connect the CH1 and CH2 connectors to supply power to the SBE-1 and S-BUS device.
- Use the provided adapter to connect the output connector to an S.BUS Hub with Cable, etc.
SBE-1 Ratings:
- No signal PWM input: Blinking
- Steady light: Lights when a regular signal is received on any channel.
FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan
PWM input connectors
- Connects all the connectors corresponding to the channel necessary to operate the S.BUS device.
- Always connect the CH1 and CH2 connectors.
- (To supply power to the SBE-1 and S-BUS device)
LED display
| 3TATE | $ISPLAY |
|---|---|
| No signal | Blinking |
| PWM input | Steady light |
Lights when a regular signal is received on any channel.
Accessories
Use this adapter to connect the output connector to an S.BUS Hub with Cable, etc..
SBE-1 ratings
(PWM->S.BUS Converter)
- PWM input: Max 10chs
- Input pulse width: 805~2,235S
- Input frame rate: 3~27.3mS
- Output signal: S.BUS
- S.BUS data rate: 100kbps
- Output frame rate: Approx. 7mS
- Operating voltage range(rated): 4.8~7.4V
- Dimensions: 23.5×33.5×9.5mm (excluding cable)
- Weight : 15g (including cable)
- Operating temperature range: -10~+45°C
- Storage temperature range: -20~+60°C
(Specifications and ratings are subject to change without notice.)
FUTABA CORPORATION
- Phone: +81 475 32 6982
- Facsimile: +81 475 32 6983 1080
Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan ©FUTABA CORPORATION 2011, 7 (1)