Schreder Briteline Gen2 1 Integrated Version Instruction Manual

BRITELINE
GEN2 1
Integrated version

INSTALLATION INSTRUCTIONS

PRODUCT OVERVIEW

BRITELINE GEN2 1 with Integrated driver

A| B| C|
609mm
23.97in| 351mm
13.81in| 436mm
1716in| 21.5kg
47.391bs

EPA – Effective Projected Area

| a = 0°| a = 30°| a = 45°| a = 70°| a = 90°
---|---|---|---|---|---
| S(m2)| CxS
(m2)| EPA
(ft2)| S
S(m2)
(m| CxS
(m2)| EPA (ft2)| S(m
S(m2)| CxS
(m2)| EPA
(ft2)| S(m2)| CxS
(m2)| EPA
(ft2)| S(m2)| CxS
(m2)| EPA
(ft2)
Si| 0.0753| 1| 0.98| 0.1333| 0.16| 2.| 0.1434| 0.18| 2.| 0.1405| 0.17| 2.| 0.1408| 0.17| 2.
S2| 0.1408| 0.17| 2.| 0.1450| 0.18| 2.| 0.1435| 18| 2.| 0.1212| 0.15| 2.| 0.0753| 0.1| 0.98
S3| 0.0398| 0.05| 0.52| 0.0398| 0.05| 0.52| 0.0398| 0.05| 0.52| 0.0398| 0.05| 0.52| 0.0398| 0.05| 0.52

MOUNTING

Screws and washers are not included inthe package!

Minimum screw requirement:

Recommended to use anti-seizing agent (Tikal Tef-Gel®) !

1. 1xM20 with large plain washer
   or

2. 2xM20 with large plain washer

Mounting dimensions

Minimum Surface Contact Area for screw fixation 250mm/9.84in

Fasteners are not included in the package!
Remark: the hatched area always need to be supported by a flat planar mounting surface as minimum.
Wider surface contact is recommended, smaller is not allowed!

ANGLE ADJUSTMENT

1. Loosen the clamp screws
   

2. Adjust tilting angle
   
   Separate scale for adjusting the distance of the optical block from the luminaire holder 50mm
   The swing arm inclination is adjustable in 10 degree increments relative to fork base.
   ALLOWED tilt angle is between -10° to 90°

3. Tighten the clamp screws
   
   Do not exceed the proposed torque levels, as it may result in fraction of the parts!

ALLOWED POSITIONING

Suspended installation

SAFETY CABLE

Steel safety cable should pass through the holes shown in the drawing in sequence.
Then connect the two ends with the lock buckle and tighten the lock bolt by hand.
For installations over 3m height: secondary safety system application is mandatory, which is appropriated for the luminaire load (e.g. safety cable)

1500mm/59.05in safety cable is supplied with the luminaire.

ELECTRICAL CONNECTION

1. Remove the R-type buckles from the junction box
   

2. Open junction box
   

3. Make the electrical connection
   

0-10V/DALI

Connection ID| Cable ID
PE/| Protective
Earth
L| Line
N| Neutral
D+| Dim +
D-| Dim –
DMX

Connection ID| Cable ID
PE/| Protective
Earth
L| Line
N| Neutral
D+| Data +
D-| Data –
Sh| Shield

Cable gland parameters

When using a larger external diameter cable, the plug and the smaller inner diameter seal hasto be removed.
When using a smaller external diameter cable, simply remove the plug.

H07RN-F , 5 x 1.5mm2

5. Close the junction box

Close junction box cover, lock the buckle and insert R-type buckles back in

RECOMMENDATIONS

1. Surrounding distances
   
   At least 1 meter distance should be kept from surrounding walls, floor, and ceiling for all types of mounting/inclination.

2. Maximum number of luminaires per MCB
   Product| Driver| MCB B type
   ---|---|---
   B10| B13| B16| B20| B25| B32| B40
   BRITELINE GEN2 1 ©220V| EUM-680MG/BG| 1| 2| 2| 3| 4| 5| 6
   BRITELINE GEN2 1 ©480V| ESM-680MG/BG| 2| 2| 3| 4| 5| 6| 7
   Product| Driver| MCB C type
   C10| 13| 16| C20| C25| C32| C40
   BRITELINE GEN2 1 ©220V| EUM-680MG/BG| 1| 2| 3| 3| 4| 5| 6
   BRITELINE GEN2 1 ©480V| ESM-680MG/BG| 3| 4| 5| 7| 9| 11| 14

AIMING DEVICE

ACCESSORIES – HOOD

SAFETY INSTRUCTIONS
The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person. Always switch off the power prior to installation, maintenance or repair activities.
RISK GROUP 2 – CAUTION! Hazardous optical radiation may be emitted from this product. Do not stare at the luminaire when operating as it may be harmful to the eyes. The luminaire should be positioned so that prolonged staring at the luminaire at a distance of less than 0.2m is not expected.
This product contains a light source of an energy efficiency class G or higher.
In case of PVC insulated mains cable, the installer MUST ensure that the WHOLE cable is protected against climatic conditions, especially UV rays and rain, by making sure that the cable is contained inside the luminaire and pole Y-connection: In case of  amage to the wire, it has to be replaced only by the manufacturer, distributor or by an expert, to avoid risks.

www.schreder.com
Rev B | 07-2023
Copyright © Schréder S.A. 2023 – Executive Publisher: Stéphane Halleux – B-4000 Liége, Rue de Mons 3 (Belgium) – The information, descriptions and illustrations herein are only of an indicative nature and subject to changes without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>