Kenmore BU4021 Bagged Upright Vacuum User Guide

Use & Care Guide
Bagged Upright Vacuum
ASPIRADORA CON BOLSA
Model/: BU4021

BEFORE USING YOUR NEW VACUUM CLEANER

Read this Use & Care Guide. It will help you assemble and operate your new Kenmore vacuum cleaner in the safest and most effective way.
For more information about vacuum cleaner care and operation, call the Vacuum Cleaner Help Line at 1-844-608-3080. You will need the complete model and serial numbers when requesting information.
Your vacuum cleaner’s model and serial numbers are located on the Model and Serial Number Plate. Use the space below to record the model number and serial number of your new Kenmore vacuum cleaner.
Model No.____
Serial No. ____
Date of Purchase __
Keep this book and your sales check (receipt) in a safe place for future reference.

PACKING LIST

Your KENMORE INTUITION® BAGGED UPRIGHT VACUUM CLEANER is packaged with the following parts and components assembled separately in the carton:

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions in this guide before assembling or using your vacuum cleaner.
WARNING!
Your safety is important to us. To reduce the risk of fire, electrical shock, injury to persons or damage when using your vacuum cleaner, follow basic safety precautions including the following:

• Use your vacuum cleaner only as described in this Use & Care Guide. Use only with manufacturer’s recommended attachments.

• Disconnect electrical supply before servicing or cleaning out the brushroll area. Failure to do so could result in the brushroll unexpectedly starting, causing personal injury from moving parts.

• Do not leave vacuum cleaner when plugged in. Unplug from outlet when not in use and before performing maintenance.

• To reduce the risk of electrical shock – Do not use outdoors or on wet surfaces.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children.

• Do not use with a damaged cord or plug. If vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped in water, call 1-844-608-3080 for assistance.

• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord away from heated surfaces.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not handle plug or vacuum cleaner with wet hands.

• Do not put any objects into openings.

• Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Do not put on chairs, tables, etc. Keep on floor.

• Do not use vacuum cleaner to pick up flammable or combustible liquids (gasoline, cleaning fluid, perfumes, etc.), or use in areas where they may be present. The fumes from these substances can create a fire hazard or explosion.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

•  Do not use vacuum cleaner without dust cup and/or filters in place.

• Always replace the dust bag after vacuuming carpet cleaners or freshener, powders, and fine dust. These products clog the filters, reduce airflow and can cause damage to the vacuum cleaner.
  Failure to replace the dust bag could cause permanent damage to the vacuum cleaner.

• Do not use the vacuum cleaner to pick up sharp hard objects, small toys, pins, paper clips, etc. They may damage the vacuum cleaner or dust bag.

•  You are responsible for making sure that your vacuum cleaner is not used by anyone unable to operate it properly.

KENMORE VACUUM CLEANER WARRANTY

If product is purchased at a Sears, Kmart or Sears Hometown retailer:
KENMORE LIMITED WARRANTY
FOR FIVE YEARS from the date of sale, this product is warranted against defects in  material or workmanship when it is assembled, operated and maintained according to all supplied instructions.
WITH PROOF OF SALE, a defective appliance will be replaced free of charge.
For warranty coverage details to obtain free replacement, visit the web page: www.kenmore.com/warranty
This warranty does not cover filters or belts, which are expendable parts that can wear out from normal use within the warranty period.
This warranty is void if this product is ever used for other than private household purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Transform SR Brands Management LLC, Hoffman Estates, IL 60179
If product is purchased from other than a Sears, Kmart or Sears Hometown retailer:
KENMORE LIMITED WARRANTY
FOR FIVE YEARS from the date of sale this product is warranted against defects in material or workmanship.
WITH PROOF OF SALE a defective product will be replaced free of charge.
The Kenmore brand is used under license. Direct all claims for warranty service to: Cleva North America, Inc., 1-844-608-3080
This warranty does not cover filters or belts, which are expendable parts that can wear out from normal use within the warranty period.
This warranty is void if this product is ever used for other than private household purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Cleva North America, Inc., Greenville SC 29607

PARTS AND FEATURES

It is important to know your vacuum cleaner’s parts and features to assure its proper and safe use. Review these before using your vacuum cleaner.
REPLACEMENT PARTS

To order a replacement part, call 1-844-608-3080.

** Please pay special attention to these hazard alert boxes, and follow any instructions given.
WARNING statements alert you to such hazards as fire, electric shock, burns and personal injury.
CAUTION** statements alert you to such hazards as personal injury and/or property damage.

ASSEMBLY INSTRUCTIONS

Before assembling the vacuum cleaner, check the PACKING LIST (page 2). Use this list to verify that you have received all the components of your new Kenmore Intuition ®Bagged Upright Vacuum Cleaner.

1. To place the body onto the nozzle, carry  the body over the nozzle and align the nozzle neck with the guides in the bodyand slowly drop into place until a ‘click’ is heard.

2.  Insert the handle into wand until you hear a ‘click’.

3. Locate the wand parallel with the body; make sure the protrusion is under upper slot as shown. Then push the wand to fit the body and then insert downward into the nozzle neck. Make sure the protrusion I is locked into upper slot and protrusion II into lower slot. A ‘click’ can be heard once you finish the wand assembly. NOTE: DO NOT tilt the wand to insert it into the nozzle neck.
   DO NOT insert the wand before placing the body onto the nozzle.

4. Insert the hose into body until you hear a ‘click’.

5. Make sure the upper and lower cord hooks are in the proper position as shown. Wrap the power cord loosely around the upper and lower cord hooks.
   NOTE: Make sure to wrap the power cord around the upper cord hook first, and then around the lower cord hook to avoid damaging the power cord.

6.  Lock power cord plug onto the power cord.

**WARNING**
Electrical Shock and Personal Injury Hazard.
Wrapping the cord too tightly with excessive stress on the cord may cause cord damage. A damaged cord is an electrical shock hazard and could cause personal injury or damage.

OPERATING INSTRUCTIONS

**CAUTION**
Moving parts! To reduce the risk of personal injury, DO NOT touch the brushroll when vacuum is on. Contacting the brushroll while it is rotating can cut, bruise or cause other injuries. Always turn off after operation. Use caution when operating near children or pets.

POWER CORD – RELEASE & USE

1. Turn the upper cord hook to either side and down to release the power cord. **WARNING**
   To reduce the risk of electric shock, this  appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

2. Detach the power cord plug from the power cord.

3.  Be sure the power cord is locked into the upper locking notch as shown. This will help manage the power cord when operating the vacuum cleaner.

4. Plug the power cord plug into an outlet located near the floor.
   WARNING
   Personal Injury and Product Damage Hazard
   · When any abnormality/failure occurs, stop using the product immediately and disconnect the power plug.
   · DO NOT use outlets above counters. Damage from cord to items in surrounding area could occur.

5.  Press the On/Off button to turn the vacuum cleaner on.

6.  Once you have completed vacuuming, press the On/Off button; unplug the power cord plug from the outlet.

7. To restore power cord after use, turn upper cord hook to the upright position.
   Then wrap cord loosely around cord hooks.
   WARNING
   Electrical Shock and Personal Injury Hazard
   Wrapping the cord too tightly puts stress on the cord and can cause cord damage. A damaged cord is an electrical shock hazard and could cause personal injury or damage.

OPERATION MODES

UPRIGHT MODE
NOTE: Make sure the vacuum cleaner is completely assembled. Do not operate vacuum cleaner without dust bag in place.

1. Release the handle by placing foot on the nozzle and pull back to change handle position.

2. Turn on the vacuum cleaner by pressing the On/Off button for cleaning bare floor. NOTE: Your vacuum cleaner has two cleaning modes: one dedicated for bare floor and one for carpets. The vacuum turns on in carpet cleaning mode, which means the brushroll is spinning. To switch to bare floor mode, simply press the Brushroll On/Off button to turn the brushroll off. We do not recommend vacuuming with the brushroll on when cleaning bare floors as this may damage your floor.

3.  Press the Brushroll On/Off button for cleaning carpets.

4. Once the vacuum is on, operate the vacuum cleaner by tilting the wand back towards you and the nozzle is flush with floor surface. NOTE: The brushroll rotates when the vacuum cleaner is in this position.
   NOTE: Brushroll does not rotate in either mode when handle is in fully upright position.
   CAUTION
   Do not allow the vacuum cleaner to remain in one spot for any length of time when the brushroll is turning. Damage to carpet may occur.

5.  Once you have completed vacuuming, press the On/Off button again and unplug the power cord from the power outlet.
   NOTE: If the brushroll is turned on, first press the Brushroll On/Off button to stop the brushroll, and then press the On/Off button to turn off the vacuum.

BAG FILL LEVEL INDICATOR
As the dust bag fills with dirt and debris, an indicator near the wand can be used to estimate the level of bag fill. Once all LEDs are illuminated red, the bag should be replaced. See page 18-19 for the dust bag replacement instructions.

illuminate to show the bag is filling.
Replace the bag when all LED lights begin to illuminate red continuously.
Two LED lights, orange continuous
Three LED lights, orange continuous
Four LED lights, red continuous

CAUTION
Make sure the dust bag is replaced when all LED lights begin to illuminate red continuously. If not, the LED lights will flash red. If the red flashing remains after replacing the dust bag, check and clean the air path as it is blocked.

BRUSHROLL STATUS INDICATOR

vacuum, and remove any blockages in the nozzle.
No LED Lights| The brushroll is off.

PERFORMANCE/SAFETY FEATURES

THERMAL PROTECTOR
This vacuum cleaner has a thermal protector which automatically trips to protect the vacuum cleaner suction motor.
If a clog prevents the normal flow of air to the motor, the thermal protector turns the motor off automatically. This allows the motor to cool in order to prevent possible damage to the vacuum cleaner.
To reset thermal protector: Turn the vacuum cleaner off and unplug the power cord from the outlet to allow the vacuum cleaner to cool and the thermal protectors to reset.
CAUTION
Always return the vacuum cleaner to the upright position before using the hose and attachments. Failure to do  so may result in overheating of the brushroll motor and can cause thethermal protectors to trip.
Check for and remove clogs, and replace dust bag if necessary. Also check and clean any clogged filters. Wait approximately 50 minutes before restarting vacuum cleaner.
BY-PASS VALVE
This vacuum cleaner has a By-Pass Valve  which prevents motor overheating anddamage. The valve opens to provide cooling air when a clog prevents normal air flow to the vacuum cleaner suction motor. You will notice a change of sound as air rushes through the valve opening. To correct the problem: remove any clogs, check and replace filters if needed, check and install new dust bag if needed.
NOTE: The By-Pass Valve may open when using attachments or when cleaning new carpet due to reduced airflow or air path is blocked, caused by the attachmentsthemselves or by new carpet lint filling the dust bag quickly.
BRUSHROLL RESET
The brushroll has built-in protection against motor damage should the brushroll jam.
If the brushroll slows down or stops, the brushroll overload protector shuts off the brushroll motor and the brushroll status indicator emits red light. The vacuum cleaner suction motor will continue to run.

To solve the problem: Turn off and unplug  vacuum cleaner, remove obstruction, thenturn on the vacuum cleaner.
NOTE: Once the brushroll motor shuts down, clear jam from brushroll and then restart the vacuum cleaner. If the problem persists, contact the vacuum cleaner helpline for assistance.
SUCTION CONTROL
To assist with push/pull force of the vacuum on surfaces like thick carpet, the  suction control valve can be opened to help reduce suction. Note that for best cleaning results, the suction control valvemust be fully closed.

• Slide to right to open the suction control and decrease suction. Opening control decreases suction for draperies and lightweight rugs.
•  Slide to left to close the suction control and increase suction. Closing control  increases suction for upholstery andcarpets.

DUST BAG REPLACEMENT

WARNING
Always unplug power cord from electrical outlet before performing any service on vacuum cleaner.

1. Pull bag chamber cover release handle out and up, hold the cover using the handle. NOTE: Do not press the dust bag release button when release bag chamber cover, or the dust bag will drop down automatically.
2.  Tilt the bag chamber as shown. Press Dust Bag Release button and the dust bag drops down automatically.
3. To install a new dust bag, insert the dust bag collar into bracket until you hear a ‘click’, and then rotate bracket down until another ‘click’ can be heard. Tuck the bag into the dust bag chamber. Be sure all sides of the dust bag are flat within the bag chamber.
4.  Place the tab on the dust bag chamber cover in the slot on the vacuum cleaner.
   Push the dust bag chamber cover into place until a ‘click’ is heard.
   NOTE: Make sure the dust bag is lockedinto place before pushing the dust bag chamber cover. The dust bag chamber cover can’t be assembled successfully if dust bag is missing or not installed into place.

FOAM FILTER CLEANING

WARNING
Electrical Shock Hazard
Unplug power cord from electrical outlet. Do not operate the vacuum cleaner without the foam filter. Be sure the filter is dry and properly installed to prevent motor failure and/or electrical shock.
Clean the foam filter with cold water as needed.
NOTE: When the cleaning of filters no longer restores vacuum cleaner suction  to full power, or the filters are worn orbroken, replace the filters. To purchase filters, call 1-844-608-3080.
Regularly clean and replace the filters to keep the vacuum’s suction power optimal.

1. Remove the dust bag as outlined in the DUST BAG REPLACEMENT section (page 18-19).

2. Remove the foam filter cover and the foam filter.

3. Wash the filter in warm soapy water, rinse and dry thoroughly by squeezing  the excess water out of the filter andallowing to air dry for 24 hours.
   NOTE: DO NOT operate without foam filter installed.
   DO NOT wash in the dishwasher.
   DO NOT install foam filter if damp.

4. Reinstall the foam filter into the foam filter cover and slide it to the slots until it is in place. Press the cover to lock it into place until a ‘click’ can be heard.
   NOTE: Replace the foam filter if it is worn or broken.

5. Reinstall the dust bag as outlined in the DUST BAG REPLACEMENT section (page 18-19).

HEPA MEDIA EXHAUST FILTER CLEANING

It is recommended to clean the HEPA media exhaust filter with cold water every year.
NOTE: When the cleaning of the filter no longer restores vacuum cleaner suction to full power, or the filter is worn or broken, replace the exhaust filter. To purchase the exhaust filter, call 1-844-608-3080.

1. Remove exhaust filter cover by pulling the tab outward at the bottom of the cover.

2. Remove the HEPA media exhaust filter from vacuum cleaner.

3. Wash with cold water only, DO NOT use detergent or soap. Allow to air dry.
   Allow parts to dry 24 hours before putting back into vacuum cleaner.
   NOTE: DO NOT operate without postmotor filter installed.
   DO NOT wash in the dishwasher.
   DO NOT install the filter if damp.

4. Reinstall the HEPA media exhaust filter into the vacuum cleaner.

5. Insert the exhaust filter cover tabs into the upper slots and lock the exhaust  filter cover into place by pressing the release tab under the cover until a clickis heard. NOTE: Make sure the exhaust filter cover is properly installed.

REMOVING CLOGS

**WARNING
Disconnect electrical supply before removing clogs. Failure to do so could result in electrical shock or personal injury.
CHECKING FLEXIBLE HOSE FOR CLOGS
If there is noticeable abnormal noise when using the vacuum or the suction power suddenly drops, it is necessary to check the air path for clogs.
Frequently check air path to make sure it is free of obstructions.
NOTE:** The four LED lights of bag fill level indicator flash red when the air path is blocked.

1. Release the wand from the body and make sure that attachments are removed from the wand.
2. Check and remove any clogs in the flexible hose and wand.
3. Reinstall the wand to the vacuum cleaner. See ASSEMBLY (page 7).

CHECKING CONNECTION HOSE FOR CLOGS
To separate the body from the nozzle, press the Lift-Up button and lift up the body.

1. Check and remove any clogs in the connection hose.
2. Reattach the nozzle onto the vacuum body.

          Vacuum Cleaner Help Line: 1-844-608-3080
8:00am-5:00pm EST, M-F
www.kenmore.com
Kenmore and the Kenmore logo are registered trademarks of KCD IP, LLC and/or Transform SR Brands LLC and are used under license.

References

• Best Appliances for Home, Kitchen, Laundry, & Cooking | Kenmore
• Warranty Information | Kenmore

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>