ROOMBANKER DSGW-290 Multi Protocol Host Gateway User Manual
- June 12, 2024
- Roombanker
Table of Contents
ROOMBANKER DSGW-290 Multi Protocol Host Gateway User Manual
Remark :
[1] Model corresponds to the model list chart above;
[2] M.2 SSD slot is reserved on the gateway, users can install SSD by
themselves
[3] Note:DSGW-290-X-N .X means different RAM and eMMC configurations.N means
support protocols.
1. Introduction
1.1 Purpose& Description
Dusun Pi4 is an IoT gateway for developers which is basically similar to Raspberry Pi4. It adopts Rockchip RK3568 processor, based on ARM Quad-core Cortex-A55 core, 64bit, 2GHz.It can run multiple systems, linux, debian, android etc. there are rich external interface, HDMI, USB, Ethernent. And compared to raspberry pi 4, it has built-in IoT wireless module, including zigbee, zwave, bluetooth, Wi-Fi, LTE. Developers can quickly develop their own gateways. and hardware encryption and also supported.
1.2 Product Feature Summary
Support audio input and output (3.5mm)
1000M Ethernet*2
2 × USB 3.0 ports
1 × micro HDMI port
SD card support: Micro SD card slot for loading operating system and data
storage
Input power: 12V DC via USB-C connector (minimum 3A1)
Power over Ethernet (PoE)–enabled (requires separate PoE HAT)
supports 2.4GHz / 5GHz dual-band WiFi, 802.11a/b/g/n/ac protocol
Support zigbee3.0, BLE5, Z-WAVE,sub-G,LoRaWAN,LTE
Support Android, Linux, Ubuntu and other operating systems
1.3 Hardware block
2.Mechanical Requirement
DSGW-291(External antennas with lora)
DSGW-290(Built-in antennas without lora)
3.Specifications
3.1 Basic parameters
3.2 Wireless protocol parameters
4. QA Requirements
4.1 Quality and Testing Information
FCC Statement
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE :
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To comply with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the user’s body and the equipment, including the antenna.
Floor 8,Building A,Wantong Center Hangzhou,China
Tel: 86-0571-86769027 / 88810480
Website: www.dusuniot.com
www.dusunremotes.com
www.dusunlock.com
References
- Dusun IoT: Embedded Hardware Vendor | IoT Gateway Sepcialist
- Dusunremotes | Custom Intelligent Remote Control Manufacturer
- Dusunremotes | Custom Intelligent Remote Control Manufacturer
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>