PRIME SmartOutlets Plus Remote Control User Manual
- June 12, 2024
- Prime
Table of Contents
PRIME Smart Outlets Plus Remote Control
Congratulations
on your purchase of PRIME Smart outlets + Remote Control! After a fast and
free download, the Prime Wire and Cable, Inc . App will walk you through the
complete setup process for your
newSmart outlets . The Remote is preprogrammed and will work out of the box.
How do I re-sync the remote if it does not switch a Smart Outlet ON or OFF?
- Only plug one Smart Outlet into a properly grounded outlet at a time.
- Press ON button on remote until LED on Smart to outlet flashes.
- Unplug_ Smart Outlet and repeat with other Smart Outlet if needed. If re-sync fails, push power button on Smart Outlet ON and push OFF button on remote until Smart Oultet power button flashes. Repeat re-sync.
- Note that you may have to replace the CR.203.2:, 3V battery in the remote by removing the screw and pushing the tabs on each side to pull out the battery tray.
- This remote does not work with any other Smart Outlets, only with this 2-pack system.
Prime warrants this product to be free from manufacturing defects for a period
of one year from the original date of purchase (“warranty period”). This
warranty is limited to the repair or replacement of this product only and
Prime is not liable for any consequential or incidental damage to other
products that may be used with this unit. This warranty is effective only if
such unit is returned to Prime not later than
thirty (30) days after the expiration of the warranty period. Warranty is void
if damage is due to neglect, misuse, alteration, modification, improper
installation, or repair by other than Prime. This warranty is in lieu of all
other warranties express or implied. Some provinces do not allow limitations
on how long an implied warranty lasts or permit the exclusion or limitation of
incidental or consequential damages, so the above limitations may not apply to
you. It is our experience that a product that fails prematurely due to a
manufacturing defect in materials or workmanship, will generally do so very
early in the product’s life cycle, often the first or second time the product
is used. Products that are returned for warranty inspection after months or
years of continuous reliable service are usually the result of normal wear and
tear, which is not considered a defect in materials or workmanship and
therefore is not covered by the warranty. This warranty gives you specific
rights, and you may also have other rights which vary from province to
province. If unit should prove defective within the warranty period, return
within the time period set forth above prepaid with the original purchase
receipt to:
- Prime Wire & Cable, Inc.
- ATTN: Timer Warranty
- 1330 Valley Vista Drive
- Diamond Bar, CA 91765
- Service – 888-445-9955 www.primewirecable.com
FCC REGULATORY STATEMENT
WARNING
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the
equipment.
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Notes
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
IC REGULATORY STATEMENT
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and Its _gain should be so chosen that the
equivalent 1sotropicaly radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This device complies with Industry Canada license–exempt RSS standard(s).
Operation is subject to the following two conditions;
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of this device.
RF exposure statement
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
However, there is no guarantee that interference will not Occur in a particular installation, If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off all on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from the to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>