Xprecia Prime Liquid Quality Control Test User Guide
- June 3, 2024
- Xprecia Prime
Table of Contents
Xprecia Prime Liquid Quality Control Test
COMPONENTS OVERVIEW
- ANALYZER 1.
- Test Strip Eject Button.
- Touch Screen
- Display.
- Power Button.
- Barcode Scanner.
- Test Strip Port.
- USB Port.
- TEST STRIP
- Test Strip insertion End.
- Test Strip Barcode.
- Sample Application Area
- TEST STRIP VIAL
- Test Strip Vial Barcode.
- XPRECIA® SYSTEMS PT CONTROLS KIT
- PT Control
- PT Contro
- CaCl, Diluent.
PREPARE PT CONTROL (LQC) SAMPLE
CAUTION
The plasma is biohazardous: always wear gloves. Use a pipette to transfer the
full contents of a CaCl, Diluent Vial to a PT Control Vial. Retain pipette for
Step 8. Replace the lid on the PT Control Vial and swirl slowly until the
color is uniform. Wait between 5 and 25 minutes before using the sample (see
Step 8
TURN THE ANALYZER ON
Hold your finger on the power button to turn the analyzer on. 3. TAP “LQC ON
Tanlochiton to hear Always wear gloves
SCAN PT CONTROL (LQC) VIAL
Tap the on-screen barcode button to scan. Hold the barcode 10 cm (4 inches)
from the bottom of the analyzer. GET STRIP. Take a strip from the test strip
vial, then close the vial firmly so the lid clicks
GET PT CONTROL (LQC) SAMPLE (from Step 1)
Swirl again briefly, then remove the lid – be gentle to avoid bubbles. You
must do the test within 25 mins of Step 1 (60 mins if refrigerated). Use
pipette from Step
APPLY PT CONTROL (LQC) SAMPLE
Only apply the sample when prompted. The sample must fill the whole of the
white semicircle 1
RESULT
If the result appears, the LQC test is passed. If an error screen appears, see
Troubleshooting in your User Guide. EJECT STRIP. Eject strip as shown. All
materials must go in a biohazard bin.
CLEAN ANALYZER
Turn over this sheet for cleaning instructions
Cleaning your analyzer
WARNINGS &GUIDANCE
- Always wear gloves when cleaning-the analyzer might be contaminated
- Clean after each and every test to ensure the analyzer is always safe to use
- Use only CaviWipes (to avoid damaging your analyzer)
- Make sure the CaviWipe is damp (not dripping): always squeeze out excess liquid into a biohazard bin
- Never let fluid gather around or enter the strip port-always keep the strip port pointing downwards during cleaning
- Before cleaning, disconnect the USB cable (if connected)
TURN ANALYZER OFF Hold your finger on the power button and select power down
to turn the analyzer off. QUICK WIPE OF ANALYZER Use a fresh CaviWipe™ and
then dispose of the wipe. REMOVE THE STRIP PORT COVER
THOROUGHLY CLEAN ANALYZER
Use a fresh CaviWipe squeeze or twist to remove excess liquid (damp not dripping). Do four vertical and four horizontal strokes on each surface (two up and down; two left and right)
CLEAN STRIP PORT COVER
Pay special attention to the strip port and channels inside the cover.
WAIT 2 MINUTES IMPORTANT
The disinfecting properties of CaviWines need this time to take effect
DRY ANALYZER AND STRIP PORT
Dry the whole analyzer and strip port cover using a lint-free tissue/cloth.
Use the same motions as Step D paying special attention to areas where fluid
ca
Items not manufactured by Universal Biosensors. CaviWines” (recommended) Lint-
free tissıues/cloth
Designed by Universal Biosensors Pty Ltd 1 Corporate Avenue, Rowville, 3178, Victoria, Australia MediMark Europe Sarl 11, rue Emile Zola, BP 2332 F- 38033 Grenoble Cedex 2, France
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>