Prime Brands Group True Wireless Earbuds With Charge Case User Manual
- June 5, 2024
- Prime Brands Group
Table of Contents
True Wireless Earbuds With Charge Case
User Manual
PRODUCT KEY
- Charging Case
- Micro USB Input ,
- Case Power Status LED
- Multi-Function Button (MFB)
- Earbud Status LED
SPECIFICATION
| Bluetooth Version | 5.0 |
|---|---|
| Battery Capacity Earbuds | 30 mAh |
| Battery Capacity Charging Station | 300 mAh |
| Continuous Playing Time’ | 3 hour |
| Charging Time | 1 hour |
| Frequency Range (Hz-KHz) | 20 Hz |
| Wireless Range | 30 ft (10 m) |
| Mic Function | Yes |
| Pick Up Function | Yes |
- Depends on volume and individual use.
CONTROL
Charging the earbuds
Put the earbuds into the charging case, the earbuds will be charged
automatically. The red status LED light will be on during charging and will
turn off when fully charged.
The Steps for dual earbud pairing (First use only).
Take out both earbuds from the charging case at the same time. The LED light
on both earbuds will be flashing blue and red. The right earbud LED will turn
off after 2 seconds. This means that both earbuds are ready to pair. Turn on
the Bluetooth on your device and search for a new device then select “Prime
TWS4 ” to connect.
How to re-connect.
The earbuds will automatically try to reconnect with the last paired device
after re-start. If not put the earbuds back into the charging case and try
again, or connect manually.
FREQUENTLY ASKED QUESTIONS
The smartphone cannot find wireless earbuds.
Check whether the earbud’s power is switched on or not. Does the status lead
light flash red and blue alternatively? If the wireless earbuds still haven’t
been found after switching power on, please restart both the earbuds and the
Bluetooth search on your phone.
There is something wrong with the wireless earbuds while using them.
Please try to re-connect with the smartphone after turning it on and
restarting the earbuds. Check the charging status of the earbuds by putting
them into the charging box until the red LED indicator is on. Then take them
out and let them try to re-connect with your device.
The wireless earbuds always disconnect or make noise when connected to a
smartphone.
The wireless earbuds’ power status is low, please recharge it. There is an
obstruction between the mobile device and the wireless earbuds, or the
wireless distance is beyond the signal range. Please do not cover the wireless
earbuds with your hands in order to maintain the continuous stability of the
signal. Try to keep the wireless earbuds and the smartphone in the same
direction.
NOTICE
- Keep it away from children: This product is not a toy.
- Do not throw or drop this product to avoid any damage.
- Do not disassemble or try to repair this product yourself.
- Do not clean this product with any chemical solvents.
- For charging, please use a charger with DC 5V output.
- Keep or use this product at a normal temperature.
- Do not expose it to a temperature above 60°/14F. Do not throw it into fire.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction
FCC ID: 2AY4Z-TWS4
©2021 Prime Brands Group. SOAR is a trademark of Prime Brands Group.
All rights reserved. All trade names are registered trademarks of the
respective manufacturers listed. Made in China.
Prime Brands Group © Brooklyn, NY ©
www.primebrandsgroup.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>