Itian V13 3 In 1 MagSafe Charger User Guide

Itian V13 3 In 1 MagSafe Charger

Product Information
This product is a device that operates within the guidelines set forth by Part 15 of the FCC Rules. It is designed to provide functionality while ensuring compliance with FCC radiation exposure limits. The device should be installed and used with a minimum distance of 20cm between the radiator and the user’s body.

Product Usage Instructions

1. Ensure that any changes or modifications to the device are approved by the responsible party to maintain compliance and avoid voiding the user’s authority to operate the equipment.
2. To prevent harmful interference, make sure that the device does not cause any interference to other devices or systems.
3. The device should be able to accept any interference received, including interference that may cause undesired operation.
4. Install and operate the device with a minimum distance of 20cm between the radiator and your body.
5. Do not co-locate or operate the transmitter in conjunction with any other antenna or transmitter.
6. The device is considered to be 80% charged. Please charge it fully before initial use for optimal performance.

Thank you for purchasing and using this product! Please read this operation instruction carefully before using this product.

Product Specification

• 3 in 1 MagSafe Charger
• Input: 5V=–2A/9V=–2A
• Cell Phone Output: 5W/7.5W/10W/15W
• Apple Watch Output: 3W
• AirPods Output: 5W
• Charging Efficiency: 70%

Applicable Devices

The list is of known existing models and will be compatible with subsequent new models.

Blinking white LED light during wireless charging to indicate charging failure. The following situation can cause failures, like charging slowly, stopping charging, and over-temperature for the charging position.

1. The adapter is not run up to standard (No PC USB output power supply).
2. The charging cable is not up to standard.
3. The phone case is too thick ( within 2mm thickness the phone case is recommended ).
4. The built-in wireless charging receiver position does not coincide with the wireless charger coil position.
5. There is a metal/magnet on the back of the cell phone or phone case.
6.  The smartphone does not support a wireless charging function.

Attention

1. Please keep the charger away from water or other liquid.
2. If you need to clean the charger, please make sure it is not connected to the power supply.
3. Operating temperature: -20-45 C.

Product Description

1.  3 in 1 MagSafe Charger, a wireless charging stand solves the charging of 3 devices.
2. Folding design, easy to carry when traveling.

Input
Connect the wireless charger and adapter with the charging cable. Please use a PD/OC3.0 adapter so that the charging will enter the fast charging mode.

LED indicator light

• White LED: Standby.
• Blue LED light: Normal charging.
• Blinking white LED light: Abnormal charging.

MagSafe Usage

FCC STATEMENT

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with another antenna or transmitter

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>