Shenzhen Itian Technology C31 Wireless Car Charger Instruction Manual

June 6, 2024
Shenzhen Itian Technology

Shenzhen Itian Technology C31 Wireless Car Charge[

Shenzhen-Itian-
Technology-C31-Wireless-Car-Charger](https://manuals.plus/wp-content/uploads/2022/03/Shenzhen-Itian- Technology-C31-Wireless-Car-Charger.webp)

Thank you for purchasing and using this product!
Please read this operation instruction carefully and keep it properly before using this product.

Product Specification

  • Fast Wireless Car Charger
  • lnput: 5V= 2A/ 9V= 2A
  • Output: 5W / 7 .5W / 1 OW
  • Charging Efficiency: 70%
  • Working frequency: 110.5K-205K

The LED light turns red during wireless charging to indicate a charging failure.
The following situation can cause failures, like charging slowly, stop charging, over-temperature for charging position.

  1. The adapter is not run up to standard.
  2. The charging cable is not up to standard.
  3. The phone case is too thick ( within 3mm thickness phone case recommended ).
  4. There is metal on the back of cell phone or phone case.
  5. Smartphone does not support wireless charging function

Attention

  1. Please keep the charger away from water or other liquid.
  2. If you need to clean the charger, please make sure it is not connected to power supply.
  3. Using Environment temperature remains -20C~45C.

Auto-Clamping Mode

  • As shown by the arrow, push the bottom bracket forward to enter the auto-clamping mode, the right and left clamping arms open automatically.
  • The bottom bracket can auto-sense and auto-move to the correct position for wireless charging of the phone based on different mobile phone sizes.

MagSafe Mode

  • As shown by the arrow, push the bottom bracket back to enter MagSafe mode, the left and right clamping arms close automatically.
  • The bottom bracket auto-move to the top of position, MagSafe mode charging, compatible with iPhone13 & iPhone12 series only.

Take off smartphone

Press the key, the clip open automatically, take your phone out.

LED indicator light shows the working status

  1. White LED light: Standby.
  2. Blue LED light: Charging normally.
  3. Red LED light: Charging abnormally.

Step to install air vent

  1. Follow the arrows to install 3 parts.
  2. Adjust the screw cap to the best active status.
  3. installation completed.

Step to install the suction cup

Shenzhen-Itian-Technology-C31-Wireless-Car-Charger-9

  1. Follow the arrows to install 3 parts.
  2. Adjust the screw cap to the best active status.Shenzhen-Itian-Technology-C32-Wireless-Car-Charger-13
  3. Paste the suction cup on the dashboard.
  4. Paste the support frame to the appropriate position
  5. installation completed.

FCC Requirement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not Installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Shenzhen Itian Technology User Manuals

Related Manuals