edenwood 972157 LED PAR Light Fitting Instruction Manual
- June 4, 2024
- edenwood
Table of Contents
edenwood 972157 LED PAR Light Fitting
Thank you!
Thank you for choosing this EDENWOOD product. EDENWOOD products are chosen,
tested, and recommended by ELECTRO DEPOT, so you can be sure you are getting a
top-quality, easy-to-use product that won’t let you down.
We’re confident your new device will be a pleasure to use every day!
Welcome to ELECTRO DEPOT.
Product overview
Parts
- A LED lens
- B Power cable with plug (supplied)
- C Adjustment knob
- D Mounting base
- E Control panel
- F DMX OUT connector
- G Display
- H ENTER button
- I DOWN button
- J Metal ring
- K UP button
- L MENU button
- M DMX IN connector
- N Signal cable
Product overview
- Unpack the product. Remove all the labels from the product. Check that it is complete and in a good condition. If the unit is damaged or faulty, do not use it and take it to your retailer or after-sales service centre.
- Keep all packaging out of the reach of children. There is a risk of accidents if children play with packaging materials.
Specifications
Product usage
Before first use
- Clean the unit ( Cleaning and maintenance).
Use
To assemble
-
Attach the hanging hook (not included) to the light-mounting base.
-
Hang the hook with the light fixed to the base, then secure the hook in place with a suitable screw and nut (not included).
The user should use a safety cable when installing the light’s housing to avoid the risk of dropping the unit. The safety cable’s technical specifications are as follows: 2 mm.
No clips or safety cables are provided as accessories. -
To adjust the beam angle: loosen the adjustment knob. Orient the light to the desired angle. Tighten the knob to secure the product in place.
Note : The appropriate fastening systems vary according to the mounting surface’s composition.
WARNING!- Always unplug the power plug from the mains socket before assembling the product.
- Use a live wire detector to ensure that no electric cables are running behind or through the surface.
-
Control panel
Numerical values indicated on the display
Using an
interconnection cable (signal cable) and DMX connector
DMX mode
DMX is an operating mode which enables the unit to be controlled via an external controller. -
Connect the signal cable from the controller output to the first light’s DMX input.
-
Connect another signal cable from the DMX output of the first light to the DMX input of the second light.
-
Repeat the above step to connect all the slave lights.
-
Connect the last light by connecting the signal cable to the DMX output connector.
Please note : the starting address for this mode must be set.
Master/slave mode
Master/slave is an operating mode that allows one light to act as a master and therefore, control all the other lights as slaves. -
Connect the signal cable to the DMX output connector of the first master light and the DMX input connector of the second slave light.
-
Repeat the step to connect all the slave lights.
-
Connect the last slave light by connecting the signal cable to its DMX output connector.
-
For more information regarding the master and slave mode settings, please refer to the table above.
Please note : only one light can be set as the master.
DMX address settings
Each light should be set with a specific starting address code. The address can be set as indicated below. -
Setting multiple lights with the same address code.
-
The lights will accept DMX512 channel starting signals from the same address code.
-
All connected lights will be controlled together.
-
Setting an independent address code for each light.
-
Please note: this is an 8-channel light fitting. If the starting address code for the first light is set to 1, then the starting code for the second light should be 9. The third should be 17, and so forth. Follow this rule to set the starting address code for each connected light.
-
Cleaning and maintenance
Cleaning and maintenance
WARNING!
Always unplug the power plug from the mains socket before carrying out any
maintenance or cleaning operations. Let everything cool completely.
Cleaning
Please note : we recommend cleaning the product every 2 weeks.
- Unplug the power plug from the mains socket.
- Use a vacuum cleaner or an air compressor and a soft brush to remove any dust that has accumulated on the external vents.
- Clean all the lenses with a dilute solution of glass cleaner or isopropyl alcohol by means of a soft lint-free cloth or a special lens cloth.
- Apply the solution to a rag or piece of cloth and slide the dirt and grime towards the outside of the lenses.
- Gently buff the optical lenses until they are streak and lint-free.
- Never use corrosive cleaners, wire brushes, abrasive scouring pads or metal/sharp tools to clean your unit.
- Thoroughly dry the unit after cleaning it.
- Store the unit in a cool, dry place, out of the reach of children and pets.
Maintenance
- Check everything on a regular basis and tighten the screws mounted on the light fitting.
- Replace any corroded screws with new ones.
- Check the condition of the surface upon which the light fitting has been installed and whether or not it is still sturdy. Make sure that there are no signs of damage or deformation.
- Check and make sure that the power cable and insulation layer have not been damaged.
- Make sure that all the circuit components have been connected correctly. Perform a thorough lighting inspection every 3 months.
Storage
- Always unplug the unit before storing it.
- Store the unit in a fresh, dry and dust-free place, out of the reach of children and pets.
- Please retain the packaging and use it to store your unit when it is not in use for an extended period of time.
Mounting
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>