VISUAL COMFORT KW 5623 Three Tier Shallow Chandelier Instruction Manual

**VISUAL COMFORT KW 5623 Three Tier Shallow Chandelier Instruction Manual

**

ASSEMBLY INSTRUCTIONS

Option 1: Canopy Mounted Driver

NOTICE:

This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED)

Phillips Screwdriver
Slotted Screwdriver
Chain Pliers
Slip Joint Pliers
Measuring Tape
Wire Cutters
Wire Strippers

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove tall mounting plate (B) from driver housing (F) and canopy (G) by removing collar ring (H) .

3. Install tall mounting plate (B) to the junction box and secure with mounting screws (D) .

4. Install driver housing (F) and canopy (G) to tall mounting plate (B) and secure with collar ring (H) .

5. Determine desired overall length, and amount of chain (I) needed.Shorten chain using chain pliers. (Keep extra chain)

6. Feed fixture wire through threaded rod (L), tube (K), fixture loop (J) , then install threaded rod (L) & tube (K) to fixture (N) and secure using fixture loop (J).

7. Attach chain (I) to collar loop and to fixture loop (J) using quick links (E). Secure quick links (E) .

8. Thread fixture wire through chain (I) .
   NOTE: When you reach tall mounting plate (B), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.

9. Separate two sides of molded wire, and strip insulation on each 5/8″.

10. Loosen collar ring (H) and let driver housing (F) and canopy (G) slipdown chain (I) carefully.
    ASSEMBLY INSTRUCTIONS
    
    NOTICE
    This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

11. Twist all fixture wires together and slip through mounting plate (B).
    NOTE: Untwist wires and separate to prepare for connection.

12. Connect driver (C) output neutral wire (black) to the fixture neutral wire (marked “-”) using wire nut (A) .

13. Connect driver (C) output hot wire (red) to the fixture hot wire (marked “+”) using wire nut (A) .
    CAUTION: Do not reverse the hot and neutral connections.

14. Wrap supply ground wire (green) around the green grounding screw(see diagram 1). Tighten.
    NOTE: It is imperative that the fixture is grounded.

15. Connect driver (C) neutral wire (white) to the supply neutral wire (usually white) using wire nut (A) .

16. Connect driver (C) hot wire (black) to the supply hot wire (usually black) using wire nut (A) .
    CAUTION: Do not reverse the hot and neutral connections.

17. Make sure all wire connections are tight, then carefully tuck into the junction box.

18. Insert driver (C) into mounting plate (B) bracket.

19. Install driver housing (F), canopy (G) to mounting plate (B) and secure with collar ring (H) .

20.  Thread alabaster shades (M) to fixture (N) . Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.

ASSEMBLY INSTRUCTIONS

NOTICE

This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

Phillips Screwdriver
Slotted Screwdriver
Chain Pliers
Slip Joint Pliers
Measuring Tape
Wire Cutters
Wire Strippers

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Place driver (C) into ceiling and route all wires through one of the knockouts in the junction box.

3. Remove tall mounting plate (B) from driver housing (F) and canopy (G) by removing collar ring (H) .
   NOTE: Driver housing (F) will be not be used for ceiling mounted assembly. Keep part and store for future use.

4. Install short mounting plate (O) to the junction box and secure with mounting screws (D) .

5. Secure collar loop (P) to short mounting plate (O) using pliers totighten locknut.

6. Install canopy (G) to short mounting plate (O) and secure with collar ring (H) .

7. Determine desired overall length, and amount of chain (I) needed. Shorten chain using chain pliers. (Keep extra chain)

8. Feed fixture wire through threaded rod (L), tube (K), fixture loop (J) , then install threaded rod (L) & tube (K) to fixture (N) and secure using fixture loop (J).

9. Attach chain (I) to collar loop (P) and fixture loop (J) using quick links (E). Secure quick links (E)
   ASSEMBLY INSTRUCTIONS
   NOTICE
   This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

10. Thread fixture wire and ground wire through chain (I).
    NOTE: When you reach mounting plate (O), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.

11. Separate two sides of molded wire, and strip insulation on each 5/8″.

12. Loosen collar ring (H) and canopy (G) slip down chain (I) carefully.

13. Twist all fixture wires together and slip through mounting plate (O).
    NOTE: Untwist wires and separate to prepare for connection.

14. Connect driver (C) output neutral wire (black) to the fixture neutral wire (marked “-”) using wire nut (A) .

15. Connect driver (C) output hot wire (red) to the fixture hot wire (marked “+”) using wire nut (A) .
    CAUTION: Do not reverse the hot and neutral connections.

16. Wrap supply ground wire (green) around the green grounding screw (see diagram 1). Tighten.
    NOTE: It is imperative that the fixture is grounded.

17. Connect driver (C) neutral wire (white) to the supply neutral wire (usually white) using wire nut (A) .

18. Connect driver (C) hot wire (black) to the supply hot wire (usually black) using wire nut (A) .
    CAUTION: Do not reverse the hot and neutral connections.

19. Make sure all wire connections are tight, then carefully tuck into the junction box.

20. Install canopy (G) to mounting plate (O) and secure with collar ring (H) .

21. Thread alabaster shades (M) to fixture (N) . Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>