VISUAL COMFORT S 2340 Brock Medium Sconce Instruction Manual
- June 12, 2024
- VISUAL COMFORT
Table of Contents
VISUAL COMFORT S 2340 Brock Medium Sconce
Product Information
- Product Name: Brock Medium Sconce
- Item Number: S 2340
- Product Description: The Brock Medium Sconce is a light fixture designed to be installed on walls. It should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well s the hazards involved. The fixture comes with necessary parts and requires assembly.
Assembly Instructions
-
Carefully remove all parts from the box and place them on a clean, soft surface. Note: After inspecting the item, replace packaging pieces (G & H) between glass and back plate until installation is complete, then remove and discard.
-
Remove the mounting plate (B) from the fixture by removing screws (D).
-
Using the mounting plate (B) as a guide, line it up with the junction box and mark anchor positions.
-
Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (E) into the holes using a hammer.
-
Install the mounting plate (B) to the junction box and secure it with mounting screws (C), then secure wood screws (F) to anchors (E).
-
Wrap the fixture ground wire (bare copper) around the green grounding screw (C) and tighten. Continue the fixture ground wire and connect it to the supply ground wire (usually green or bare copper) using a wire nut (A). Note: It is imperative that the
fixture is grounded. -
Connect the fixture neutral wire (white) to the supply neutral wire (usually white) using a wire nut (A). Connect the fixture hot wire (black) to the supply hot wire (usually black) using a wire nut (A). Caution: Do not reverse the hot and neutral connections.
-
Make sure all wire connections are tight, then carefully tuck them into the junction box.
-
Install the fixture to the mounting plate (B) by securing it with screws (D).
-
Remove and discard packaging (G & H) between glass and backplate.
Care Instructions
Clean the fixture only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
Item # S 2340
NOTICE:
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction and
operation of it, as well as the hazards involved. Inspect item and contents
carefully. If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.
FEATUYRES
TOOLS REQUIRED (NOT INCLUDED):
- Phillips
- Screwdriver
- Slotted Screwdriver
- Drill
- Pencil
- Hammer
ASSEMBLY INSTRUCTIONS
-
Carefully remove all parts from the box. Place on a clean, soft surface.
NOTE : After inspecting item, replace packaging pieces (G & H) between glass and back plate until Installation is complete, then remove and discard. -
Remove mounting plate (B) from fixture by removing screws (D).
-
Using the mounting plate (B) as a guide, line up with the junction box and mark anchor positions.
-
Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (E) into the holes using hammer.
-
Install mounting plate (B) to the junction box and secure with mounting screws (C), then secure wood screws (F) to anchors (E).
-
Wrap fixture ground wire (bare copper) around the green grounding screw (C) . Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A).
NOTE : It is imperative that the fixture is grounded. -
Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
-
Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (A).
CAUTION : Do not reverse the hot and neutral connections. -
Make sure all wire connections are tight, then carefully tuck into the junction box.
-
Install fixture to mounting plate (B) by securing with screws (D).
-
Remove and discard packaging (G & H) between glass and backplate.
Care Instructions
Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>