NICOR TAR Select LED Troffer Retrofit Kit Instruction Manual
- October 27, 2023
- NICOR
Table of Contents
TAR Select LED Troffer Retrofit Kit
TAR SELECT LED TROFFER RETROFIT KIT INSTALLATION INSTRUCTIONS Model(s): TARS114U, TARS122U, TARS124U
WARNING – Risk of fire or electric shock. The electrical rating of these products are 120-277 Vac, the installer must determine whether they have 120-277V at the luminaire before installation.
WARNING – Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
WARNING – Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation
The installation must only be performed by a licensed electrician. To prevent death, injury or damage to property, this product must be installed in accordance to National Electrical Code (NFPA70) in the US or Canadian Electrical Code (CSA 22.1) in Canada.
Disconnect power and wait until fixture has cooled before installing the product or servicing it. MIN. 90°C SUPPLY CONDUCTORS
What’s In The Box
Tools Needed
This LED Troffer Retrofit Kit requires very few tools for installation. A drill or a screwdriver and a pair of wire cutters.
NOTE: The existing fluorescent luminaires housing shall be larger than dimensions described in the below table:
Housing Designation Overall Inner Dimensions
2’x2′ – 24.0in x 23.9in x 3.1in (610mm x 608mm x 78mm)
2’x4′ – 48.0in x 23.9in x 3.1in (1220mm x 608mm x 78mm)
1’x4′ – 48.0in x 12.0in x 3.1in (1220mm x 305mm x 78mm)
1 Carefully unpack the fixture from its packaging. Inspect product for defects due to shipping.
2 Prior to installation, disconnect all incoming power to fixture. Remove existing hardware (lens/lens frame, parabolic louver, reflectors/ballast covers, brackets, lamps/lamp holders). Leave supply and grounding leads.
NICOR, Inc. 2200 Midtown Place NE, Albuquerque, NM 87107 P: 800.821.6283 F: 800.892.8393 www.nicorlighting.com August 11, 2020 3:48 PM rev 1.0
3 Install end brackets to each end of the fixture by gently lifting recessed fixture and placing the end brackets between the fixture and T-grid. Secure the brackets to the fixture using the provided #8×1/2″ self-drilling screws. (There are two hole sets to allow for clearing fixture features that may obstruct the screws.
4 Install side brackets between fixture and grid, making sure to insert tabs of side brackets into slots of end brackets.
5 Insert hinge pin of the TAR main body into the keyholes of the end bracket, then slide to the end of the slots.
6 Hook the safety cables into the holes located on the end brackets. Connect wiring as shown. Grey and purple wiring are for 0-10V dimming systems. Cap off if not used.
7 To adjust CCT or Lumen output, set the switch positions on the back of the fixture to the desired settings.
8 Swing TAR main body up into place and lock using the locking latches on each side.
Note:
- Power selection switch is a three-position switch that will adjust light output: low/medium/high.
- CCT selection switch is a three-position switch that will adjust Color Temperature between 3500K, 4000K, or 5000K.
9 Turn power on and verify that the troffer is lit.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
NICOR, Inc. 2200 Midtown Place NE, Albuquerque, NM 87107 P: 800.821.6283 F: 800.892.8393 www.nicorlighting.com August 11, 2020 3:48 PM rev 1.0
LED EXPRESS LIMITED WARRANTY
Subject to the exclusions below, each NICOR LED product, including the LED
electronics and components of a property installed NICOR LED product, will be
free from defect in materials and workmanship for a period of ve (5) years
from the original date of purchase. The product shall be considered defective
only if 10% or more of the product’s LED components fail. NICOR LED product
warranty covers the following performance criteria: LED Light Output will be
maintained above 70% of initial output; LED color temperature will not shift
more than 200K in CCT; LED driver will operate within NICOR specications; and
the xture nish, excluding natural aluminum or brass products, will not exhibit
cracking, peeling, excessive fading, or corrosion during the warranty period.
Exceptions apply as dened in NICOR’s product specication sheets, which are
incorporated by reference herein. This limited warranty is provided to you,
the purchaser of the product identied on Seller’s invoice, as your exclusive
remedy and applies only to NICOR products that have been purchased from an
authorized NICOR Distributor; the product was new and in an unopened NICOR
package at the time of installation; and the NICOR product was installed by a
licensed electrician or under the supervision of a licensed electrician and
used by consumers in the United States or Canada when accompanied with this
warranty. This warranty extends only to the rst consumer purchaser and is not
transferable. A consumer wishing to invoke the terms of this limited warranty
must rst obtain a RGA number within 30 days of discovery of the defect, and
return the product to NICOR for inspection. Once veried to be covered by this
limited warranty, NICOR will, at its sole discretion, repair, replace, or
refund the purchase price of any product that does not conform to this limited
warranty. If NICOR, at its sole discretion, determines that the product should
be repaired or replaced, this warranty is limited to the reasonable,
customary, and necessary costs and expenses associated with the
repair/replacement. This warranty requires that all repair/replacement
estimates and costs, including but not limited to equipment rental (if any),
and any other cost or expense to be incurred in the repair/replacement of the
product, be approved in advance and in writing by NICOR. FAILURE TO OBTAIN
NICOR’S ADVANCE WRITTEN APPROVAL OF ALL REPAIR/REPLACEMENT COSTS AND EXPENSES
IN WRITING SHALL VOID THIS LIMITED WARRANTY. THIS LIMITED WARRANTY DOES NOT
COVER THE FOLLOWING: · Defects or damages resulting from improper
installation, operation, storage, misuse or abuse, accident, or neglect; ·
Defects or damages resulting from improper service, testing, adjustment,
installation, maintenance, alteration, connection to out-of-specication
electrical service, corrosive or damp environments, or connection to
incompatible equipment or devices (e.g., connecting non-dimmable lighting
products to dimmers); · Damage which occurs in transit; · Power surges or
overheating due to external conditions · Acts of nature including but not
limited to lightning strikes ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE SHALL BE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY,
OTHERWISE THE REPAIR, REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN
LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. IN NO EVENT SHALL NICOR BE
LIABLE, WHETHER IN CONTRACT OR IN TORT (INCLUDING NEGLIGENCE) FOR DAMAGES IN
EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, OR FOR ANY INDIRECT, INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS,
LOSS OF BUSINESS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH
THE ABILITY OR INABILITY TO USE THE PRODUCT TO THE FULL EXTENT THESE DAMAGES
MAY BE DISCLAIMED BY LAW.
SHARE YOUR EXPERIENCE WITH US
SCAN the QR or visit www.nicorlighting.com/support/survey
FOLLOW US
NICOR, Inc. 2200 Midtown Place NE, Albuquerque, NM 87107 P: 800.821.6283 F:
800.892.8393 www.nicorlighting.com August 11, 2020 3:48 PM rev 1.0
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>