PURe geaR Magnetic Wireless Car Charger User Manual

: June 12, 2024
: PURe geaR

PURe geaR Magnetic Wireless Car Charger User Manual

Specs

Magnetic Wireless Car Charger

USB-C™ Input: 5V/2A, 9V/2.22A, 12V/1.67A
Output: Up to 15W

Qualcomm® Quick Charge™ 3.0 Car Charger

Output: 6‒6V/3A; 6‒9V/2A; 9‒12V/1.5A

Caution

DO NOT place any credit cards or other types of magnetic material near the charging pad. Do not attempt to disassemble the wireless charging pad as it may short circuit or damage the product. Keep at least 8” (20cm) distance between implantable medical devices such as pacemakers, cochlear implants, etc. Keep this product in a dry and ventilated space. Do not place in direct heat or use in high humidity environments. Do not use organic solvents to clean surface.

Instructions

Attaching the VENT MOUNT:

Unscrew the large socket nut and push vent clip ball joint into the hole until it snaps into
Screw the socket nut back on until tight – this locks the vent clip onto the wireless charging pad and holds the adjustable support base in

Attaching the SUCTION MOUNT:

Unscrew the large socket nut and push vent clip ball joint into the hole until it snaps into
Screw the socket nut back on until tight – this locks the vent clip onto the wireless charging pad and holds the adjustable support base in place

Instructions

Using your Magnetic Wireless Car Charger :

Connect the USB-A to USB-C cable to the USB-C port of the Magnetic Wireless Car
Connect the USB-A connector into the included car charger and plug it
Place the back of your Apple iPhone® MagSafe® device against the Magnetic Wireless Car Charger until it automatically aligns and snaps into *‡ Charging will begin automatically.

* __ Works with MagSafe cases. Non-MagSafe cases must be removed before charging.
‡If you prefer to strengthen the Magnetic Wireless Car Charger, use the enclosed ring sticker; however, it is not necessary**

Instructions

Placing the Metal Ring Sticker on older iPhones and Androids without

magnetic functionality built-in:

Place the metal sticker in the middle of the back of your phone. To find the middle of the phone:

Ensure your Magnetic Wireless Car Charger is plugged in. 2.Place the metal sticker on the magnetic Magnetic Wireless

Car Charger, with the adhesive side facing up and away from the charger.

Peel off the protective liner from the
Make sure the phone’s volume is turned on Hold the back of your phone (or your phone with a case) close to the metal sticker but don’t let them touch , and line up the wireless charging position of the phone and the charger until the phone makes a sound and starts charging.
Close the gap between your phone and the Magnetic Wireless Car Charger and let the metal sticker attach to your phone or your
Firmly press on the sticker to adhere to your phone or For best results, let the metal ring sticker set for 30 minutes or longer before use.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator & your body.

FCC Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

FCC Interference Statement (cont.)

This equipment generates, uses and can radiate radio frequency energy; if not installed and used in accordance with the instructions, maybe cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving
Increase the separation between the equipment and
Connect the equipment into and outlet on a circuit different form that to which the receiver is
Consult the dealer or an experienced radio/TV technician for

IC Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference;
This device must accept any interference, including interference that may cause undesired operation of the

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 10cm between the radiator & your body.

Lifetime Warranty

This product is fully warranted against defects in materials and workmanship for the lifetime of the product, so long as the manufacturer continues to make this product. If a product fails due to a manufacturing defect, we will replace it upon proper proof of purchase by the original purchaser. Replacement product will be subject to shipping and handling charges. Damages through normal wear and tear, alteration, misuse, neglect, accident, service by anyone other than the authorized service center, or act of God, are not covered by this warranty. For all warranty claims, the product must be returned in accordance with PureGear’s return policy.
All trademarks and trade names are used for reference purposes only and are the property of their respective owners.