SERVER 85783 Remote Dispensing System Instruction Manual

Remote Dispensing System
Remote Pump with 36″ Hose
SINGLE POUCH SYSTEM
85783
Remote Pump with 36″ Hose
TWIN POUCH SYSTEM
85784
Instruction Manual

Use with pouches up to 3 gallons with either 16mm fitment or 38mm connector.

Thank You for purchasing our Remote Dispensing System. This manually operated system simplifies high-volume dispensing, eliminating the hassle of a CO2 driven dispenser.
HIGH VOLUME—HIGHLY CONVENIENT

REMOTE SYSTEM PARTS

MOUNTING BRACKET DETAILS

SAFETY

According to food and safety regulations, most foods must be stored and/or served at certain temperatures or they could become hazardous. Check with local food and safety regulators for specific guidelines.
Be aware of the product you are serving and the temperature the product is required to maintain. Server Products, Inc. cannot be responsible for the serving of potentially hazardous product.
IMPORTANT
Clean, rinse, sanitize, and dry parts daily or regularly to comply with local sanitization requirements.
NSF International lists this pump as:
“Not acceptable for dispensing potentially hazardous foods.”

QUICK START

YOU WILL NEED:

• A qualified person to install the countertop bracket
• Screwdriver, (4) screws, router and/or saw equipment

1. INSTALL THE COUNTERTOP BRACKE
   • Choose a location with easy access and convenient height for pump.
   • Allow room for slack in hose during set-up, pouch replacement and take-down.
   IMPORTANT TIP:
   Do not locate countertop hole directly above pouch support(s). Offset the hole to leave space for pump and hose below.
   • Use cutout template included to mark, cut and drill holes.
   • Secure the bracket with four screws.

2. INSERT THE PUMP INTO BRACKET
   Always clean pump first.
   Refer to separate instructions for the pump.
   • Insert pin on rear of bracket into hole on rear of lid.
   • Pull the under-counter lever forward to allow front pin of bracket into front hole of lid.
   • Release lever to secure front bracket pin.
   • Tighten thumbscrew to lock lever.

3. ATTACH HOSE TO PUMP
   • Slide hose onto valve connector at bottom end of pump.
   • Rotate hose clamp turn-key clockwise to secure hose.
   TIP: Hose may be trimmed if length is excessive.

4. PREPARE POUCH(ES)
   Place condiment pouch on flat surface with pouch connector or fitment facing upward.
   If pouch has
   38MM EXTERNAL CONNECTOR
   • Remove pouch cap.
   • Screw dispensing cap onto connector. If pouch has
   16MM INTERNAL FITMENT
   • Screw dispensing cap onto adapter.
   • Position adapter directly over center of pouch fitment.
   • Press adapter down to pierce through film in pouch fitment. Pump is fully engaged when top surface of pouch fitment touches adapter rim.

5. PLACE POUCH(ES)
   INTO POUCH SUPPORT(S)
   Locate dispensing cap in front slot directed downward for best evacuation of condiment.

6. PLACE SUPPORT(S) BENEATH COUNTER
   Twin pouch system includes wire rack for pouch supports.

7. CONNECT HOSE TO POUCH
   Snap hose end onto dispensing cap.

8. PRIME PUM P
   Repeatedly press pump knob until condiment is drawn up from pouch and hose below.

SWITCHING POUCHES

WHEN A CONDIMENT POUCH BECOMES EMPTY…

1. DISCONNECT HOSE FROM EMPTY POUCH
   Press button on side of hose coupling to release.

2. SNAP HOSE COUPLING ONTO DISPENSING CAP ON NEW POUCH
   See page 5 for how to prepare pouch(es).
   DID YOU KNOW?
   The hose coupler and dispensing cap prevent leaks when hose is disconnected.

DISASSEMBLY

1. DISCONNECT HOSE FROM PUMP
   Turn hose clamp turn-key counter-clockwise to loosen the hose.

2. DISCONNECT HOSE FROM POUCH
   Press button on side of hose coupling to release.

3. REMOVE PART(S) FROM POUCH
   Unscrew dispensing cap from pouch.
   IF USED: Remove adapter from 16mm pouch fitment.
   IMPORTANT: Only throw away empty pouch. Keep any dispensing cap and adapter fitment.

4. REMOVE PUMP FROM COUNTER BRACKET
   • Loosen thumbscrew on bracket.
   • Pull lever under counter to release front hole of lid from front pin of bracket.
   • Lift pump free from pin in back of bracket.

CLEANING

Refer to separate instruction manual for pump cleaning.

1. CLEAN
   After disassembling, thoroughly clean all washable parts with soap and hot water.

2. RINSE fully with clear water.

3. SANITIZE all parts according to local sanitization requirements. All parts in contact with food must be sanitized.

4. AIR DRY all parts fully.

YES!
Use dishwashing soap and hot water.

Use supplied brush to clean inside hose.

• External surfaces may be wiped clean with a clean damp cloth.
• Glass and surface cleaners approved for use in food contact areas may be used.
• Do not use abrasive, caustic or ammonia based cleansers.
• Do not use metal scrapers or cleaning pads that could scratch surfaces.

SERVER PRODUCTS LIMITED WARRANTY

This Server product is backed by a two-year limited warranty against defects in materials and workmanship. See Server-Products.com for details.

GENERAL SERVICE, REPAIR OR RETURNS

Before sending any item to Server Products for service, repair, or return, contact Server Products customer service to request a Return Authorization Number. Merchandise must be sent to Server Products with this number. Service is extremely prompt. Typically, units are repaired and ship out within 48 hours.
Merchandise being returned for credit must be in new and unused condition and not more than 90 days old and will be subject to a 20% restocking charge.
CUTOUT Template
Full Scale 1:1

NEED HELP?
Server Products Inc.
3601 Pleasant Hill Road
Richfield, WI 53076 USA
Chat with us!
spsales@server-products.com
262.628.5600 | 800.558.8722
Please be prepared with your Model, P/N and
Series located on the lid or base of the unit. Manual EM_01898_RevD 042022

References

• products.com
• Server Products
• Chat now
• Server Products
• Warranty Information | Server Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>