POWER FIST 9096884 5 Shelf Steel Shelving Unit User Manual

5-Shelf Steel
Shelving Unit
User Manual

Please read and understand all instructions before use. Retain this manual for future reference.

SPECIFICATIONS

INTRODUCTION

Store a variety of tools, equipment and household items with this galvanized steel and MDF shelving unit. Each of the 5 shelves is adjustable by up to 1-/18 in. and capable of holding 385 Ib.

SAFETY

WARNING! Read and understand all instructions before using this tool. The operator must follow basic precautions to reduce the risk of personal injury and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection and maintenance instructions.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A notice is an alert that there is a possibility of property damage, injury or death if certain instructions are not followed.
V4.0 5-Shelf Steel Shelving Unit 9096884
DANGER! This notice indicates an immediate and specific hazard that will result in severe personal injury or death if the proper precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that could result in severe personal injury or death if the proper precautions are not taken.
CAUTION!
This notice indicates a potentially hazardous situation that may result in minor or moderate injury if proper practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will result in equipment or property damage, but not personal injury.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit and free of distractions. Place lights so you are not working in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away from the work area.
3. Store unused tools properly ina safe and dry location to prevent rust or damage. Lock tools away and keep out of the reach of children.
4. Place this shelving unit only on a surface that is flat, level and capable of handling the unit and its full weight capacity.
5. Do not place in areas of high humidity in order to avoid damage to the shelving board.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian Standards Association (CSA) or American National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side protection for the eyes. Eye protection equipment should comply with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of work performed.
2. Wear protective clothing designed for the work environment and tool.
3. Non-skid footwear is recommended to maintain footing and balance in the work environment.
4. Wear steel toe footwear or steel toe caps to prevent a foot injury from falling objects.

PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs, alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with the moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and balance enables better control in unexpected situations.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to the tool safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specific function. Do not modify or alter this tool or use it for an unintended purpose.
2. Do not use the tool if any parts are damage broken or misplaced. Repair or replace the parts.
3. Do not exceed the overall maximum load capacity. The weight rating is based on an evenly distributed load.
4. Do not allow children to use this device without supervision. This device is not a toy.
5. Centre load the shelves where possible. Uneven distribution of weight could lead to tipping and damage.
6. Do not climb or sit on the shelving unit.
7. It is recommended that this shelving unit be anchored to a wall after assembly in order to ensure full stability and safety.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the missing part before operating. Failure to do so could result in a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
Make sure that all items in the Identification Key are included.
IDENTIFICATION KEY
A MDF shelving board (5)
B Vertical support (8)
C Long shelf brace (10)
D Short shelf brace (10)
E Middle shelf brace (5)
F Corner bracket (4)
G Foot (8)

ASSEMBLY & INSTALLATION

Letter references in parenthesis (A) refer to the included Identification Key.

1. Take 2 of the vertical supports (B) and connect them at the lowest possible position with 1 of the short shelf braces (D) (Fig. 1).

2. Install a second short shelf brace at the desired position (Fig. 1).

3. Place 4 of the feet (G) on the bottom of the 4 vertical supports (Fig. 2).

4. Connect the vertical supports using 2 of the long shelf braces (C) (Fig. 3). a. Make sure the attachment is proper and secure (Fig. 4).

5. Insert a corner bracket above the second short shelf brace position on each of the 4 vertical supports (Fig. 5). a. Arubber hammer or mallet is recommended for this step to avoid denting or other damage.

6. Attach the remaining long and short shelf braces at the desired positions.

7. Locate the middle shelf brackets (E) and attach them across the middle of each set of long shelf braces (Fig. 6).
   a. Make sure the attachment is proper and secure (Fig. 7).

8. Place the MDF shelves onto the completed shelving unit (Fig. 8)

9. Place the remaining 4 feet on the top of the vertical supports.

10. Ensure that all connections are proper and secure.

11. Carefully move the shelving unit to the desired location.

12. If possible, affix the shelving unit to a wall using appropriate hardware (not included).

GARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient, easier to control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace damaged or worn components. Only use identical replacement parts when servicing.
3. Only use accessories intended for use with this tool.
4. Maintain the tool’s labels and name plates. These carry important information.
   If unreadable or missing, contact Princess Auto Ltd. for replacements.

WARNING! Only qualified service personnel should repair the tool. An improperly repaired tool may present a hazard to the user and/or others.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function properly or parts are missing. If unable to do so, have a qualified technician  service the tool.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>