DENALI LAH.22.10302 Ducati DesertX Crash Bar Light Mounting Brackets Instruction Manual

June 12, 2024
DENALI

DENALI-logo

DENALI LAH.22.10302 Ducati DesertX Crash Bar Light Mounting Brackets

DENALI-LAH-22-10302 Ducati-DesertX-Crash-Bar-Light-Mounting-Brackets-
product

Product Information

The product is the Crash Bar Light Mounting Brackets designed specifically for the Ducati DesertX LAH.22.10302. It is manufactured by DENALI and can be purchased from their website, DENALIELECTRONICS.COM.

The package includes the following items:

  • Upper Light Mounting Bracket – Left (LAH.22.10302-01) – Quantity: 1
  • Upper Light Mounting Bracket – Right (LAH.22.10302-02) – Quantity: 1
  • M5 x 25mm Flanged Button Head Screw – Quantity: 4

Additionally, a 3mm wrench is required for installation.
Note : These brackets are designed to work with Ducati DesertX Steel Engine Cover Crash Guards – 96781851AA.

Product Usage Instructions

  1. Installing The Light Mount
  2. Install the Upper Light Mounting Bracket – Left  (LAH.22.10302-01) to the Clutch side of the bike with two M5 x 25mmScrews. Use a 3mm allen driver to tighten the screws.
  3. Install the Upper Light Mounting Bracket – Right (LAH.22.10302-02) to the Throttle side of the bike with two M5 x 25mm Screws. Use a 3mm allen driver to tighten the screws.
  4. Note : Install light pods on top of the bracket shelf, with the light bracket facing downwards, mounting to the top surface of the light mount.

It is important to position the lights towards the bottom of the slotted holes of their swivel brackets for optimal installation. This ensures that the DENALI LED lights are mounted tightly against the crash bars.
For any further questions or assistance, you can contact DENALI’s gear experts at 401.360.2550 or visit their website at WWW.DENALIELECTRONICS.COM.

Thank you for choosing DENALI

We know you would rather be riding your bike than wrenching on it, so we go the extra mile to make sure our instructions are clear and as easy to understand as possible. If you have any questions, comments, or suggestions don’t hesitate to give our gear experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM

Please Read Before Installing

DENALI products should always be installed by a qualified motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. DENALI takes no responsibility for damages caused by improper installation. Caution: When installing electronics it is extremely important to pay close attention to how wires are routed, especially when mounting products to the front fender, front forks, or fairing of your motorcycle. Always be sure to turn the handlebars fully left, fully right, and fully compress the suspension to ensure the wires will not bind and have enough slack for your motorcycle to operate properly.

Installation Tips

We strongly recommend using medium-strength liquid thread locker on all screws, nuts, and bolts. It is also important to ensure that all hardware is tightened to the proper torque specifications as listed in your owner’s manual. For included accessory hardware please refer to the default torque specifications provided below. Inspect all hardware after the first 30 miles to ensure proper torque specifications are maintained.

Bolt Size in-lbs ft- lbs Nm
M3 10.0 in-lbs 1.0 Nm
M4 23.0 in-lbs 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 13.5 ft-lbs 18.0 Nm
M10 30.0 ft-lbs 41.0 Nm
M12 52.0 ft-lbs 71.0 Nm

Hardware Sizing Guide

Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc. Remember, the length of a screw or bolt is measured from the start of the “mounting surface” to the end of the screw, so only include the screw head when measuring countersunk screws.DENALI-LAH-22-10302 Ducati-
DesertX-Crash-Bar-Light-Mounting-Brackets-fig- \(3\)

What’s In The Box

DENALI-LAH-22-10302 Ducati-DesertX-Crash-Bar-Light-
Mounting-Brackets-fig- \(1\)

Kit Contents

  • Upper Light Mounting Bracket – Left (LAH.22.10302-01)………Qty 1
  • Upper Light Mounting Bracket – Right (LAH.22.10302-02)………..Qty 1
  • M5 x 25mm Flanged Button Head Screw………………………Qty 4

Tools Required: 3mm Wrench

Note : This bracket set is designed to work with Ducati Desert “Steel Engine Cover Crash Guards” – 96781851AA

Installing The Light Mount

DENALI-LAH-22-10302 Ducati-DesertX-Crash-Bar-
Light-Mounting-Brackets-fig- \(2\)

Install the Mounts

  • Step One : Install the Upper Light Mounting Bracket – Left (a) to the Clutch side of the bike with two M5 x 25mm Screws (c). Tighten with a 3mm allen driver.
  • Step Two: Install the Upper Light Mounting Bracket – Right (b) to the Throttle side of the bike with two M5 x 25mm Screws (c). Tighten with a 3mm Allen driver. (Not shown)

Note : Install light pods on top of the bracket shelf, with the light bracket facing downwards, mounting to the top surface of the light mount.
The brackets are designed to keep DENALI LED lights mounted tightly against the crash bars. Optimal installation requires the lights to be positioned toward the bottom of the slotted holes of their swivel brackets.

Ducati DesertX
LAH.22.10302

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DENALI User Manuals

Related Manuals