DENALI DNL.WHS.23900 Ducati DesertX DialDim Wiring Harness Instruction Manual
- June 12, 2024
- DENALI
Table of Contents
DENALI DNL.WHS.23900 Ducati DesertX DialDim Wiring Harness
Product Information
- Product Name: DialDimTM Wiring Harness
- Compatible with: Ducati DesertX
- Model Number: DNL.WHS.23900
- Manufacturer: DENALI
- Website: www.denalielectronics.com
Product Usage Instructions
Please Read Before Installing
- We strongly recommend using medium strength liquid thread locker on all screws and bolts.
- Tighten all hardware to the proper torque specifications listed in your owner’s manual.
- Inspect all hardware after the first 30 miles to ensure proper torque specifications are maintained.
Installing The DialDim Controller
- Locating the Battery
- To gain access to the battery, remove the Seat.
- Remove both of the terminals from the battery, starting with the positive + (Red Terminal).
- Positioning The Controller
- Position the DialDim Controller underneath the rider’s seat, behind the battery, against the left (clutch) side of the battery box.
- Remove the fuse from the DialDim fuse holder.
- Connect both of the battery leads to the battery, starting with the ground – (Black Terminal).
- Re-install the fuse to the DialDim Fuse holder.
- Use double-stick tape and/or zip-ties to securely mount the DialDim Controller to the splash guard. Ensure there is enough clearance for the seat to be re-installed.
Installing The DialDim Harness
Connect the DialDim Wiring Harness to the following connectors
- Connectors located behind windscreen
- OEM Headlight Harness
If you have any further questions or need assistance, please contact our experts at 401.360.2550 or visit our website at www.denalielectronics.com.
Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go
the extra mile to make sure our instructions are clear and as easy to
understand as possible. If you have any questions, comments, or suggestions
don’t hesitate to give our experts a call at 401.360.2550 or visit
WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle
technician. If you are unsure of your ability to properly install a product,
please have the product installed by your local motorcycle dealer. DENALI
takes no responsibility for damages caused by improper installation. Caution:
When installing electronics it is extremely important to pay close attention
to how wires are routed, especially when mounting products to the front
fender, front fork, or fairing of your motorcycle. Always be sure to turn the
handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to
operate properly.
Installation Tips
- We strongly recommend using medium strength liquid thread locker on all screws and bolts.
- It is also important to ensure that all hardware is tightened to the proper torque specifications as listed in your owner’s manual.
- For included accessory hardware please refer to the default torque specifications provided below.
- Inspect all hardware after the first 30 miles to ensure that proper torque specifications are maintained.
Bolt Size | in-lbs | ft- lbs | Nm |
---|---|---|---|
M3 | 10.0 in-lbs | – | 1.0 Nm |
M4 | 23.0 in-lbs | – | 2.5 Nm |
M5 | 44.5 in-lbs | 3.5 ft-lbs | 5.0 Nm |
M6 | 78.0 in-lbs | 6.5 ft-lbs | 9.0 Nm |
M8 | – | 13.5 ft-lbs | 18.0 Nm |
M10 | – | 30.0 ft-lbs | 41.0 Nm |
M12 | – | 52.0 ft-lbs | 71.0 Nm |
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts,
spacers, etc. Remember, the length of a screw or bolt is measured from the
start of the “mounting surface” to the end of the screw, so only include the
screw head when measuring countersunk screws.
What’s In The
Box?
Kit
Contents
- DialDim™ Wiring Harness (Ducati DesertX)………………………..Qty 1
Harness Overview
Overview of Harness
This DialDim Wiring Harness enables plug-&-play connection between our standard DialDim Lighting Controller and the Ducati DesertX. The harness replaces the universal Posi tap style input harness that is included with the universal DialDim Controller, enabling you to simply connect in-line at the factory headlight, horn, and turn signal connectors.
Installing The DialDim Controller
Locating the
Battery
The DesertX’s battery is located underneath the rider seat.
- Step One: To gain access to the battery, remove the Seat.
- Step Two: Remove both of the terminals from the battery, starting with the positive + (Red Terminal).
Positioning The Controller
- Step Three: Position the DialDim Controller underneath the rider’s seat, behind the battery, against the left (clutch) side of the battery box.
- Step Four: Remove the fuse from the DialDim fuse holder, then connect both of the battery leads to the battery, starting with the ground – (Black Terminal). Then re-install the fuse to the DialDim Fuse holder.
- Step Five: Use double-stick tape and/or zip-ties to securely mount the DialDim Controller to the splash guard. Be sure there is enough clearance for the seat to be re-installed.
Installing The DialDim Harness
Locating Connectors & Installing the Harness
The DesertX DialDim Harness will be connected in-line to four factory harness connectors: Headlight, Right Turn Signal, Left Turn Signal, & Horn
- Step One: To gain access to the Head Light and Turn Signal connectors, remove the windscreen. They are all located within a cavity on the front side of the dash.
- Step Two: The headlight connector is located on the back of the factory headlight housing, it is a black 6-pin connector. Disconnect the factory headlight connector from the headlight housing, then connect the “Headlight Pass-Through Connector” of the DialDim Harness in-line.
- Step Three: The Left and Right Turn Signal Connectors are located beside the Head Light Connector. They are both white, 2-Pin connectors that are labled “L” and “R”. Disconnect the factory Turn Signal Connectors from the indicators, and connect the respective “Left Turn” and “Right Turn” Pass Through Connectors of the DialDim Harness in-line.
- Step Four: The horn connector is located directly on the factory horn, which is located at the center of the motorcycle, just above the radiator. Disconnect the factory horn connector with the RED wire then, connect the “Horn Pass-Through Connector” of the DialDim Harness in-line.
DialDim™ Wiring Harness
DENALIELECTRONICS.COM
OUTFITTING GUIDE
Documents / Resources
|
DENALI DNL.WHS.23900 Ducati DesertX DialDim Wiring
Harness
[pdf] Instruction Manual
DNL.WHS.23900 Ducati DesertX DialDim Wiring Harness, DNL.WHS.23900, Ducati
DesertX DialDim Wiring Harness, DialDim Wiring Harness, Wiring Harness,
Harness
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>