TerraTrike Maverick Nicollet Bike and Ski User Manual

October 30, 2023
TerraTrike

Terra Trike Maverick Nicollet Bike and Ski User Manual
754yju5tf v5  f4 rdf cfe sfefcx
TerraTrike Maverick Nicollet Bike and Ski

Alignment

Inflate tires before performing alignment. The Maverick alignment measurement is approximately 30¼” (center tread to center tread), though slight variance is possible. Most importantly, make sure the alignment remains neutral with a rider seated in the trike.
Alignment

Direct Steering Stack Assembly

Assemble the steering stack as shown. Grease the steerer tube before inserting into head tube. Remove any excess grease from steered tube before installing handlebar. Grease axle before installing wheel. Torque axle bolt to 23-25Nm.

Parts List

1 M6x18 Bolt TT000415
2 Direct Steer Hub mount Cap TT000161
3 Twist Handlebar – RH TT000655
Twist Handlebar – LH TT000646
Twist Handlebar – Pair TT000271
M6x16 Bolt (not pictured) TT000294
4 M20 Washer TT000254
5 Direct Steer Hub mount – RH TT000828
Direct Steer Hubmount – RH TT000829
Direct Steer Hubmount – Pair TT000653
6 Bushings (pre-installed) TT000809

Chain Tube Setup

Mount the chain tube assemblies as shown below. Ensure the chain tubes do not rotate in the clamps after tightening the pinch bolts.

Upper:
Chain Tube Setup

Lower:
Chain Tube Setup

Upper Assy Chain Tube, 102cm LDPE TT000540 1
Chain Tube Clamp, Rov/Ram/Mav TT000152 1
M5x18 Pan Head (phillips) SS N/A 2
Lower Assy Chain Tube, 56cm LDPE TT000548 1
Chain Tube Clamp, Traveler TT000422 1
Spacer, 20mm L, 8mm AD x 10mm OD TT000123 1
M5x18 Pan Head (Phillips) SS N/A 1
M8x40mm BHCS SS TT000278 1

Chain Routing

x8 Model
Chain Routing
i3 and i8 Models
Chain Routing
Cable Routing RH x8 Model
Chain Routing
i3 and i8 Models
Chain Routing

Cable Routing LH (applies to all models)
Cable Routing

**i3 Bell Crank Installation (Refer to Shimano Dealer Manual DM-SG0005-02)


**

Insert the push rod (A) into the hub axle.
Bell Crank Installation

(z) About 14 mm
The push rod should protrude about 14 mm from the end face of the hub axle.
(A) Pushrod

While pushing the bell crank into the hub axle, align the serrations inside thebell crank with the hub nut (C), and continue push until the crank comes into contact with the end face (E) of the hub axle.

While keeping the parts in this position, tighten the bell crank fixing bolt (A) onto the hub axle.

Make sure that the edge (D) of the window is aligned with the end face of the hub axle.

(A) Bell crank fixing bolt
(B) 5 mm hexagon wrench or 10 mm spanner
(C) Hub nut
(D) Edge of the window
(E) End face of the hub axle
Tightening torque

Set the REVOSHIFT lever to 2.

Next, turn the cable adjustment barrel (A) to align the red line (D) on the push rod with the end (C) of the hub axle.
Bell Crank Adjustment

(A) Cable adjustment barrel
(B) Push rod
(C) End of the hub
(D) Red line on the push rod
(E) Yellow lines
(F) Yellow part of the link

NOTICE

During adjustment, check the two yellow lines through the window from above.

While turning the crank, move the REVOSHIFT lever from 3 to 1 then back to 3. Repeat this two or three times and check to see that the gears are being shifted. Move the REVOSHIFT lever from 1to 2 again and make sure that the red line on the push rod is aligned with the end of the hub axle. If they are not aligned, perform readjustment.

After adjusting the bell crank IV, fix the cable adjustment barrel with the cable adjustment nut (A).

(A) cable adjustment nut

Tightening torque

| 15-25N-m

**i8 Cassette Joint Installation (Refer to Shimano Dealer Manual DM- CASG001-00)


**

Set the REVOSHIFT lever to 1.

(z) setto1

(A) REVOSHIFT lever

After checking that the end of the outer casing s securely set in the cable adjustment barrel of the REVOSHIFT lever, attach the inner cable mounting bolt unit to the inner cable.
Cassette Joint Installation

(w) 10mm
(X) Pass the inner cable through the hole.
(y) 101mm
(z) Pull the inner cable when securing.

(A) Inner cable mounting nut (Black)
(B) Inner cable mounting washer (silver)
(C) Inner cable mounting bolt (Silver)
(D) Inner cable mounting bolt unit

Tightening torque

| 3.5-5.5Nm

NOTE

  • This inner cable mounting bolt unit is designed only for CJ-NX10, CJ-NX40, CJ-8520, and CJ-8540. 11-speed mounting bolt units cannot be used.
  • The tool is shipped ready to be used for CJ-NX10 and CJ-8520.
  • When installing the inner cable mounting bolt unit, use the setting tool TL-CJA0 (Y70898020).
  • For CJ-NX10 and CJ-8520, use the front side of TLCJ40.

Front side of TL-CJ40
Front side

Bring the cable around to the cassette joint pulley, hold it so that the inner cable fixing nut is facing outwards (towards the fork end), and then slide the flats part of the inner cable fixing washer into the gap in the pulley.

(A) Flats part of inner cable fixing washer
(B) Gap in pulley
(C) Inner cable fixing nut
(D) Pulley

Turn the cable 60° counterclockwise and attach it to the hook.
Front side

(z) Turn the cable 60°

(A) Hook

Attach the inner cable to the pulley as shown in the illustration, pass the inner cable through the slit in the bracket, and then insert the end of the outer casing securely into the outer casing holder.

800.945.9910
www.TerraTrike.com
4460 40th St. SE | Grand Rapids, Ml 49512 USA
Icons

Revised 6/2022

Terra Trike Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals