KUZCO CNP06AC LED Ceiling Canopy Installation Guide
- June 12, 2024
- KUZCO
Table of Contents
KUZCO CNP06AC LED Ceiling Canopy
Product Information
- Model: CNP06AC
- Manufacturer: Kuzco Lighting
- Technical Support: 1-855-855-8926
- Address: 19054 28th Avenue Surrey, BC Canada V3Z 6M3
- Website: kuzcolighting.com
Product Usage Instructions
- Remove the LED ceiling canopy from its original packaging.
- Take out the mounting plate (1c) from inside the canopy (2a) by unscrewing the decorative nuts (2c).
- Attach the mounting plate (1c) to the electrical junction box (1a) using the junction box screws (1e) provided in the hardware package.
- Ensure there is sturdy wood behind the drywall and secure the mounting plate (1c) to the mounting surface using wooden screws (1g) and plastic anchors (1f) for additional support.
- To adjust the fixture height, press and hold the wire gripper (2g), slide the wire to the desired length, and then release the wire gripper (2g) to secure it in place.
- If using thicker wire, follow the wire strain relief instructions illustrated in Illustration 1. Remove the wire grippers (2g), pull the wire through the nut (3a), washer (3b),threaded cylinder (3c), and wire strain relief (3d). Secure the threaded cylinder (3c) to the canopy (2a) with the nut (3a) and washer (3b). Thread the wire strain relief (3d) onto the threaded cylinder (3c). Adjust the wire length by pushing and pulling, then secure it with the set screw (3e).
- Make the appropriate electrical connections using the wire nuts (1b) provided in the hardware package. Connect the black wire to hot L, the white wire to neutral N, and the ground wire to GND.
- Align and insert the mounting plate screws (1d) through the holes on the canopy (2a), and secure them with the decorative nuts (2c).
START FROM HERE
- Make sure POWER is COMPLETELY OFF at the fuse box
- Have your fixture installed by a qualified licensed electrician
- Prepare everything in a clear area
- Wear gloves at all time during this installation
- Read instructions carefully before you start assembly
- Keep this installation sheet for future reference
Technical Support: 1-855-855-8926
Installation
- Remove the canopy from it’s original packaging
- Remove the mounting plate (1c) from within the canopy (2a) by removing the decorative nuts (2c)
- Attach the mounting plate (1c) to the electrical junction box (1a) using the junction box screws (1e) provided in the hardware package
- Make sure to reinforce the wood behind the drywall and secure mounting plate (1c) to mounting surface with wooden screws (1g) and plastic anchors (1f) for extra support.
- To change fixture height, push and hold wire gripper (2g), slide wire to desired length and then release wire gripper (2g) to secure
- Wire strain relief (for thicker wire) (see illustration 1): Removewire grippers (2g). Pull wire through nut (3a), washer (3b), threaded cylinder (3c) and wire strain relief (3d). Secure threaded cylinder (3c) to canopy (2a) with nut (3a) and washer (3b). Thread wire strain relief (3d) to threaded cylinder (3c). Slide wire to desired length by pushing and pulling and secure with set screw (3e)
- Make proper electrical connections (black to hot “L”, white to neutral “N”, ground to “GND”) with wire nuts (1b) provided in hardware package
- Align and insert mounting plate screws (1d) through holes on canopy (2a), secure with decorative nuts (2c)
19054 28th Avenue Surrey, BC Canada V3Z 6M3
- T: 604 538 7162
- TF: 1-855 85 KUZCO
- F: 604 538 7196
- W: kuzcolighting.com
- 20210419
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>