CONAIR HV26HCX Ion Shine Instant Heat Hairsetter Instruction Manual

hot clips

Instruction & Styling Guide
Model CHV26HCX

For your safety and continued enjoyment of this product, always read the instruction book carefully before using it.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING KEEP AWAY FROM WATER
DANGER – To reduce the risk of electrocution:

1. Always unplug this appliance immediately after using it.
2. Do not use it while bathing or in the shower.
3. Do not place or store appliances where they can fall or be pulled into a tub or sink.
4. Do not place in or drop into water or other liquids.
5. Do not reach for an appliance that has fallen into the water. Unplug immediately.

WARNING – To reduce the risk of burns, electrocution, fire, or injury to persons:

1. An appliance should never be left unattended when plugged in.
2. Do not pull, twist or wrap line cord around the appliance.
3. Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain disabilities.
4. Use this appliance only for its intended use as described in the manual. Do not use attachments not recommended by Conair.
5. Never operate this appliance if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to an authorized service center for examination and repair.
6. Keep the cord away from heated surfaces.
7. Never block the air openings of the appliance or place them on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
8. Never use while sleeping.
9. Never drop or insert any object into any opening or hose.
10. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
11. Do not use an extension cord with this appliance.
12. Do not touch metal “radiator” strips that hold rollers, as they will be hot.
13. Do not touch the metal rails that heat the clips.

SAVE THESE INSTRUCTIONS

OPERATING INSTRUCTIONS

How to operate your hairsetter with heated clips:

1. Place hairsetter on a firm, flat surface. With the lid closed, plug the cord into the outlet. This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

2. Once plugged in, the red light will go on and the rollers will heat up quickly.
   Rollers are ready to use when the ready dot on the roller turns transparent white. (Please refer to HOW TO CURL YOUR HAIR for further instruction.)

3. Allow rollers and clips to heat with the lid closed, as this will provide the fastest, most efficient heat-up. Once the rollers reach your desired temperature, you can begin setting your hair.

4. Hair should be clean and dry or slightly damp – never wet – when setting. For tighter curls, allow rollers to heat longer at a higher temperature.

5. Never leave your hairsetter on and unattended. Always unplug the hairsetter when not in use. Allow the hairsetter to cool down after use, and store in a safe place.

USER MAINTENANCE

Your hairsetter is designed for household use and is virtually maintenance- free. This product represents the highest standards of workmanship and engineering research. If cleaning becomes necessary, disconnect the appliance from the power source. Allow the setter to cool. Clean the unit and the heating rails with a cloth. (Occasionally you may want to clean your rollers. Use a damp cloth and mild detergent or soap.) If any abnormal condition occurs, unplug the hairsetter, allow it to cool, and return it to an authorized service representative for repair.
STORAGE
Allow hairsetter to cool. Handle cord carefully to prolong its life; avoid jerking or straining at plug connections. Store hairsetter out of reach of children in a safe, dry location.

HOW TO CURL YOUR HAIR

1. Place ends of the hair on roller and wind toward the scalp. Roll up hair firmly remove the clip from the heated rail and secure over the roller. Place another clip on an aluminum rail for heat-up. Continue to add clips to the heating rail as rollers are added to the hair.

2. The firmness of the curl is regulated by the diameter of the roller and the length of time the roller is left in your hair.

3. For tight, firm curls, use smaller rollers and leave them in the hair for at least ten minutes before removing them. For soft, wavy curls, use larger rollers and remove rollers after a shorter period of time.

4. Removing roller: Hold roller in one hand while removing heated clip with the other. Gently drop roller (DO NOT PULL) and let curl bounce back after roller has been completely removed. Let cool for one minute for a firmly set curl, and then style your hair into a look that lasts for hours.

IMPORTANT: After using the hairsetter several times, you will find the best roller selection and the best timing for the texture of your hair and for the result you desire.

MEDIUM ROLLERS
Use on short hair to create a fullness and tight curl. Tight curls can be used at the nape of the neck and to frame your face.

LARGE ROLLERS
Use medium to long hair to create a looser curl that’s bouncy and full of body.

JUMBO ROLLERS
Use medium to long hair to create the smooth sleek lines of softer, sophisticated hairstyles.

TO ORDER ExTRA ROLLERS

Rollers come packed three of the same size to a carton. Rollers are sold by carton only.

Please add postage and handling to all orders.
Postage and handling are as follows: Orders up to $5.00: add $.50 to order. Orders from $5.01 to $10.00: add $1.00 to order. Orders of $10.01 and over: add $1.50 to order.
MAIL ORDER TO:
Conair Corporation
150 Milford Road, East Windsor, NJ 08520
Service Department
7475 North Glen Harbor,
Glendale, AZ 85307
Include return name and address and model number of replacement rollers. Please make the check payable to Conair Corporation.
WARNING:
IF YOU THINK THE POWER IS OFF WHEN THE SWITCH IS OFF, YOU’RE WRONG.

KEEP AWAY FROM WATER

Everyone knows that electricity and water are a dangerous combination. But did you know that an electrical appliance is still electrically live even if the switch is off? If the plug is in, the power is on. So when you are not using your appliances, keep them unplugged.
ALWAYS UNPLUG SMALL APPLIANCES

LIMITED ONE-YEAR WARRANTY

Conair will repair or replace (at our option) your unit free of charge for 12 months from the date of purchase if the appliance is defective in workmanship or materials.
To obtain service under this warranty, return the defective product to the service center listed on the back, together with your purchase receipt and $5.00 for postage and handling. California residents need only provide proof of purchase and should call 1-800-366-0937 for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 12 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED  WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 12-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, ExPRESS OR IMPLIED, WHATSOEVER.
Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you. This
the warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Please register this product at:
www.conair.com/registration
Service Center
Conair Corporation
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307

**©2012 Conair Corporation
150 Milford Road, East Windsor, NJ 08520
7475 N. Glen Harbor Blvd., Glendale, AZ 85307
IB-11476**
12PH132584

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>