tala CP-OAK-LRG-01-EU Large Canopy Installation Guide

tala CP-OAK-LRG-01-EU Large Canopy

Thoughtful lighting, responsibly designed in London.
Thank you for making the switch to Tala. Discover the full Tala family at tala.co.uk

Product Information

The Large Canopy is a thoughtfully designed lighting fixture created by Tala, a London-based company. It is suitable for indoor use only and operates on a 240V mains voltage. This canopy is compatible with the Tala family of products, which can be found at tala.co.uk. It comes with a ceiling bracket, ceiling plate, cord grips, safety tethers, junction box, and necessary fixings.

The product has the following specifications:

• SKU: CP-OAK-LRG-01-EU
• SKU: CP-WALT-LRG-01-EU
• SKU: CP-ASH-LRG-01-EU
• For indoor use only
• IP20 rated
• 220 – 240V~

Please note that installation and maintenance of this light fitting should be carried out by a qualified electrician.

BEFORE STARTING

We advise the fitting of our canopy and pendants to be performed by a qualified electrician. Please read through these instructions before commencing work, and keep them for future reference. Please take extreme care when carrying out these instructions.

IMPORTANT
This light fitting must be connected to the supply earth. If your lighting circuit does not have an earth, ask a qualified electrician to provide an earth facility. This light fitting is suitable for indoor use only. This fitting operates on 240V mains voltage. Please visit our website to see our recommended dimmers.

WARNING
You must switch off electricity supply at the mains during installation and maintenance. We strongly recommend that you withdraw the fuse or switch off the circuit breaker whilst work is in progress. Do not only turn off the wall switch. All fittings must be installed in accordance with current Building Regulations and IEE Wiring Regulations.

RECOMMENDED EQUIPMENT

• Small Flat-head and Phillips-head screwdriver
• Wire strippers
• Insulation tape
• 17mm spanner
• 7mm spanner
• Power drill with 10mm and 5mm drill bit

(Always use the correct drill bit for the material)

Scan me for more technical help:

Provided Components

• A. x1 Ceiling Bracket
• B. x1 Ceiling Plate
• C. x12 Cord Grips
• D. x3 Safety Tethers and Clips
• E. x1 Junction Box
• F. x1 M4 20MM Bolt

INSTALLATION INSTRUCTION

1. STEP 1
   Unhook the three safety tethers from the plate (B) Set ceiling bracket (A) with tether (D) to one side.

2. STEP 2A – REVERSE OR REPLACE DISPLAY PANEL (OPTIONAL)
   Remove panel (B) and display disk (3) by loosening nut 1 and washer (2). To display the alternative finish, rotate disc (3) 180 degrees. Note, not all display panels have an alternative finish.
   STEP 2B
   Re-assemble the plate in the same order and fasten it securely with nuts and washers (2). Tighten these firmly with a spanner/wrench.

3. STEP 3
   Once you have chosen the hanging positions of your pendants, with a 5mm drill bit, drill small pilot holes through panel from the back side (3) Please take your time drilling these holes. We recommend you clamp the plate onto a sacrificial surface (4). This will stop the plate moving and help give a clean hole on the front surface.

4. STEP 4
   Flip the panel (3) over to the visible side and, using a 10mm drill bit, drill final holes through the pilots on the visible side. Again we recommend using a sacrificial surface.

5. STEP 5
   Fasten cord grips through the holes you have drilled using the toothed washers (5) and nuts (6) Tighten these firmly with a spanner/wrench.

6. STEP 6
   Attach (A) to the ceiling using screws and plug. Make sure to Use screws and plugs that are appropriate for the ceiling type.

7. STEP 7
   Attach ceiling plate (B) to ceiling bracket A using safety tether clips (D).

8. STEP 8
   Thread all nine pendant cables E through ceiling plate cord grips (C ).

9. STEP 9
   Pull cables through to your desired length. See end of this guide for our recommended lengths and distance between bulbs. Using a flathead screwdriver, tighten set screws (C) to secure them.

10. STEP 10
    Cut off excess cable and strip wires to expose the copper core. Maintain all double insulation.

11. STEP 11
    Connect the pendants, plate and mains wiring as shown.

12. STEP 12
    Lift (B) to sit flush with (A). Make sure the pins (1) are located at the opening of the bayonet fitting (2).

13. STEP 13
    Rotate plate (B) anti-clockwise until the pin is locked into the (1) bayonet mechanism (2). Secure plate (B) in place using bolt (G) There will be a small shadow gap between the canopy and the ceiling.

PENDANT DISPLAY GUIDE

ADJUSTING THE CORD
To adjust the cord to your desired length, using a flat head screw driver, loosen the grub/set screw (1) and push the cable up into the ceiling plate. Secure the cable in place by re-tightening the grub screw. Maintain all double insulation.

MINIMUM CORD LENGTH (A)
For all bulbs shortest recommended cord length is 350mm.

DISTANCE BETWEEN PENDANTS (B)
Recommended minimum distance between pendant, dependant on bulb style, are as follows:

• Voronoi I – 150mm
• Voronoi II – 200mm
• Voronoi III – 350mm
• Sphere IV – 150mm
• All other bulbs – 100mm

PENDANTS – RECOMMENDED CABLE LENGTHS

1. SCENARIO 1
   Above a coffee or dining table, or where height is required for seated tasks .

2. SCENARIO 2
   Above side tables, or where height is required for storage.

3. SCENARIO 3
   Above a kitchen island or bar, or where height is required for standing tasks .

4. SCENARIO 4
   Above a stairwell or walkway, or where height is required for walking underneath.

WARRANTY AND AFTER-CARE

This product has a two-year warranty. If there appears to be a functional defect with the product during this time, please contact our team at customerservice@tala.co.uk. Please note, the flexible cable attached to this luminaire cannot be replaced; if the cable is damaged, recycle the luminaire and seek a replacement.

This symbol indicates that electrical and electronic equipment (WEEE) should not be mixed with general household waste. For recovery and recycling, please take this product to a designated collection point where it will be accepted free of charge. Many retailers offer this in-store. Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment.

Join the Community
Instagram: @tala | Facebook: talaHQ | Pinterest: TalaLED | Tag: lighttoliveby
Tala Energy Ltd. 25B Vyner Street, London E2 9DG | hello@tala.co.uk
Tala Europe B.V, Bertus Aafjeshove 40, Nieuwegein 3437JN, Netherlands

References

• Tala | Shop Official Tala® Lighting | Light to Live By

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>