Wi-Tek WI-PS305G Gigabit PoE Switch Installation Guide
- June 12, 2024
- Wi-Tek
Table of Contents
Wi-Tek WI-PS305G Gigabit PoE Switch
Product Information
The product is a 24GE+2SFP Gigabit PoE Switch that is designed for network connectivity and power supply to PoE-enabled devices. It comes in various models with different port configurations and power budgets. The switch supports VLAN and CCTV modes for optimized network performance.
- Model: 24GE+2SFP Gigabit PoE Switch
- Interface: 24 100/1000Mbps RJ45 PoE+ Ports, 2 1000Mbps Combo SFP Ports
- Power Budget: Different power budgets available depending on the model
- Power Supply: AC 100-240V
- Default Mode: The transmission distance of PoE port can be up to 100m with 100Mbps.
- VLAN Mode: All downlink ports are isolated from each other, but can communicate with uplink ports.
- CCTV Mode: CCTV mode ensures voice and video applications remain clear and lag-free. The transmission distance of PoE port can be up to 250m, but the rate is limited to 10Mbps.
Product Usage Instructions
Follow the steps below to use the 24GE+2SFP Gigabit PoE Switch:
- Unbox the package and check the contents. The package should include the switch itself along with any additional accessories.
- Select an appropriate power supply source and connect it to the switch’s grounding interface.
- Choose the desired mode of operation – Default, VLAN, or CCTV – based on your network requirements.
- Connect your PoE-enabled devices to the RJ45 PoE+ ports on the switch. Make sure the devices are within the specified transmission distance.
- For uplink connectivity, use the Combo SFP Ports to connect to other network devices.
- Observe the LED indicators on the switch to monitor its status. The PWR indicator should be on if the device is powered on normally.
- Verify the link and activity status of the ports by checking the Link/Act indicator. It should be blinking if there is data transmission.
- If using 1000Mbps negotiation, ensure that the 1000Mbps indicator is on and blinking to indicate successful negotiation and data transmission.
Refer to the product manual for more detailed instructions and specific information related to your model.
Package Contents
Take WI-PS326GF as an example:
Hardware Introduction
Front Panel
WI-PS326GF
DIP Switch Description
Default| The transmission distance of PoE port can be up to 100m with 100Mbps.
VLAN| All downlink ports are isolated from each other, but can communicate
with uplink ports.
CCTV| CCTV mode is to ensure voice and video applications remain clear and
lag-free.
Extend| The transmission distance of PoE port can be up to 250m, but the rate
is limited to 10Mbps
LED Light
PWR (Power indicator)| Off: the device is power off or failed
On: the device power on is normal
Link/Act indicator| Off: ports link down
On: ports link up
Blinking: data on TX/RX
1000Mbps indicator| Off: The negotiate speed is 10/100Mbps, not 1000Mbps
On: The negotiate speed is 1000Mbps and ports link up
Blinking: The negotiate speed is 1000Mbps and data on TX/RX
Model| Interface| Power Budget| Power Supply| Default
Mode| Extend Mode| VLAN Mode| CCTV Mode
---|---|---|---|---|---|---|---
WI-PS305G| Port 1: 1000Mbps RJ45 PoE++ 60W Port
Port 2-4: 1000Mbps RJ45 PoE+ Ports 2 1000Mbps RJ45 Ports
| 65W| AC 100~240V| √| Port 1-2| √| ×
WI-PS308G| Port 1: 1000Mbps RJ45 PoE++ 60WPort
Port 2-8: 1000Mbps RJ45 PoE+ Ports 2 1000Mbps RJ45 Ports
| 120W| AC 100~240V| √| Port 1-2| √| ×
WI-PS305GF| 4 1000Mbps RJ45 PoE+ Ports 1 1000Mbps RJ45 Port 1 1000Mbps SFP
Slot| 65W| AC 100~240V| √| Port 1-4| √| ×
WI-PS309GF| 8 1000Mbps RJ45 PoE+ Ports 1 1000Mbps RJ45 Port 1 1000Mbps SFP
Slot| 150W| AC 100~240V| √| Port 1-8| √| ×
WI-PS310GF| 8 1000Mbps RJ45 PoE+ Ports 2 1000Mbps SFP Slots| 150W| AC
100~240V| √| √| √| ×
WI-PS318GF| 16 1000Mbps RJ45 PoE+ Ports 2 1000Mbps SFP Slots| 350W| AC
100~240V| √| ×| √| √
WI-PS320GF| 16 1000Mbps RJ45 PoE+ Ports 2 1000Mbps Combo SFP Ports| 350W| AC
100~240V| √| ×| √| √
WI-PS326GF| 24 1000Mbps RJ45 PoE+ Ports 2 1000Mbps SFP Slots| 400W| AC
100~240V| √| ×| √| √
WI-PS328GF| 24 1000Mbps RJ45 PoE+ Ports 4 1000Mbps Combo SFP Ports| 400W| AC
100~240V| ×| ×| ×| ×
WI-PS348G| 48 1000Mbps RJ45 PoE+ Ports| 600W| AC 100~240V| ×| ×| ×| ×
WI-PS105F| 4 100Mbps RJ45 PoE+ Ports 1 1000Mbps SC Fiber| 65W| AC 100~240V|
×| ×| ×| ×
WI-PS110F| 8 100Mbps RJ45 PoE+ Ports 1 1000Mbps Combo Port| 150W| AC
100~240V| √| √| √| ×
WI-PS128GF| 24 100Mbps RJ45 PoE+ Ports 4 1000Mbps Combo Ports| 350W| AC
100~240V| ×| ×| ×| ×
WI-PS150GF| 48 100Mbps RJ45 PoE+ Ports 2 1000Mbps Combo Ports| 700W| AC
100~240V| ×| ×| ×| ×
Hardware Installation
Installation
-
Wall mounted
(Only for WI-PS305G, WI-PS308G, WI-PS305GF, WI-PS309GF) -
Rack mounted
(Except WI-PS305G, WI-PS308G, WI-PS305GF, WI-PS309GF)
Warranty Card
Username|
---|---
Address|
Telephone No.|
Purchase Shop|
Purchase Address|
Product Model No.|
Purchase Time|
Serial No.|
Dealer Signature|
- If the product defects within three months after purchase, we will provide you a new product of the same model.
- If the product defects within the three-year warranty period, we will provide the professional maintenance service.
- Proof of purchase and a complete product serial number are required to receive any services guaranteed as part of the limited warranty.
- Any other defects that are not caused by workmanship or product quality, such as natural disaster, water damage, extreme thermal or environmental conditions. sticker damaged, warranty card losing will disqualify the product from limited warranty.
Wireless-Tek Technology Limited
Address: Biaofang Technology Building 402, Bao’an street, Baoan
District,Shenzhen City, Guangdong, China
Website:www.wireless-tek.com
Tel: 86-0755-32811290
Email:sales@wireless-tek.com
Technical Support:tech@wireless-tek.com
www.wireless-tek.com