Karlik ICUSB-1 Single USB Charger User Manual
- June 12, 2024
- KarliK
Table of Contents
Karlik ICUSB-1 Single USB Charger
Product Information: ICUSB-1 / ICUSB-3 Single USB Charger
The ICUSB-1 / ICUSB-3 charger is designed to charge smartphones, MP3 players, and other electronic devices. It is important to ensure that the charger complies with the charging parameters of the device before connecting it.
| Specification | ICUSB-1 / ICUSB-3 |
|---|---|
| Number of USB ports (type A) | 1 |
| Nominal input voltage | 110-240 V~ |
| Nominal input current | 0.25 A |
| Nominal output voltage | 5 V DC |
| Nominal output current | 1 A / 2 A |
| Ingress protection degree | IP 20 |
Warranty Conditions
A warranty period of 12 months is provided from the date of purchase. In
case of any defects, the defective ICUSB-1 / ICUSB-3 charger along with the
proof of purchase should be sent to the manufacturer or seller. The warranty
does not cover mechanical damages, defects resulting from unauthorized
repairs, or improper use of the product. The warranty period will be extended
for the duration of the repair.
Assembly Instructions
IMPORTANT: The installation must be carried out by a qualified person
with the power supply disconnected and in compliance with national safety
standards.
Refer to Figure 2 for the correct connection to the installation. Improper connection may damage the charger or cause it to work incorrectly. The USB charger mechanism consumes idle power supply of approximately 0.2W.
Figure 1: [Image Description]Figure 2: [Image Description]
Ensure that the charger is installed correctly and safely according to the provided instructions.
USER MANUAL: ICUSB-1 / ICUSB-3 SINGLE USB CHARGER
Specification of ICUSB-1 / ICUSB-3 single USB charger
The ICUSB-1 / ICUSB-3 charger is intended to charge devices like smartphones,
MP3 players and other electronic equipment. Before connecting the device,
check compliance of the charger with charging parameters of the given device.
Specification
| Number of USB ports (type A)) | 1 |
|---|---|
| Nominal input voltage | 110-240 V~ 50/60Hz |
| Nominal input current | 0,25 A |
| Nominal output voltage | 5 V DC |
| Nominal output current | 1 A / 2 A |
| Ingress protection degree | IP 20 |
Warranty conditions
Warranty is granted for a period of 12 months of the date of purchase. The
defective ICUSB-1 /ICUSB-3 charger along with the proof of purchase should be
sent to the manufacturer or to the seller. Warranty does not include
mechanical damages, defects resulting from unauthorized repairs and improper
use of the product.
Warranty period will be extended for the duration of the repair.
ASSEMBLY INSTRUCTIONS
- Remove the glass panel (1) with the label applying a knife or a flat screwdriver in the recess (3).
- Remove the screw (2).
- Dismantle the USB charger module (4).
- Remove the spacer frame (5) from the assembly block (7). Pull away the block tabs or pull the frame tightly to do this.
- Set the assembly block in the box (9) with tabs or screws at the box (8).
- Insert the spacer frame in the external frame (6) and snap the entire set on the tabs protruding from the assembly block.
- Connect the wires of the installation to the USB charger module as shown in Figure 2.
- Insert the USB charger module in the intermediary unit.
- Screw down the intermediary unit to the assembly block.
- Attach the label and glass pane.
NOTE!
The installation must be done by a person with sufficient qualifications, with
power supply disconnected, and must comply with national safety standards.
The connection to the installation should be done as shown in Figure 2. With
improper connection, the charger may be damaged or may work incorrectly.
USB charger mechanism with idle power supply consumes less than about 0,2W.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>