ATEN US434 4 Port USB 3.1 Gen 1 Peripheral Sharing Device Instruction Manual

ATEN US434 4 Port USB 3.1 Gen 1 Peripheral Sharing Device

US234 / US3324 Package Contents

• 1 USB 3.1 Gen Peripheral Sharing Switch
• 2 USB 3.1 Gen 1 Type-8 to Type-A Cables 1.2M
• 1 USB 3.1 Gen 1 Type-8 to Type-C Cable 1.8M (US3324 only)
• 1 Remote Port Selector
• 1 User Inst ructions

US434 / US3344 Package Contents

• 1 USB 3.1 Gen 1 Peripheral Sharing Svvitch
• 2 USB 3.1 Gen 1 Type-B to Type-A Cables 1.2M
• 2 USB 3.1 Gen 1 Type-8 to Type-A Cables 1.8M
• 2 USB 3.1 Gen 1 Type-8 to Type-C Cables 1.8M (US3344 only)
• 1 Remote Port Selector
• 1 User Instructions

Hardware Review

US234 / US434 / US3324 / US3344 Front and Top View

➊ Console Indicator LED
➋ USB 3.1 Gen 1 Device Ports
➌ Micro USB Power Input
➍ Remote Port Selector

US234 / US434 I US3324 I US3344 Rear View

➎ PC Ports
➏ Remote Port Selector Jack

Hardware Installation

➊ Plug the USB 3.1 Gen 1 Type-A or Type-C end of the included USB cables into your computers (US234 / US3324: up to 2 computers; US434 / US3344: up to 4 computers) and plug the USB 3.1 Gen 1 Type-8 end of the included USB cables into the back of the US234 I US434 / US3324 / US3344.
➋ Plug your USB peripheral devices into the US234 I US434 / US3324 / US3344.
➌ Plug the Remote Port Selector into the Remote Port Selector jack on the US234 / US434 / US3324 / US3344.
➍ Switch from one computer to another by pressing the Remote Port Selector.
The Console Indicator LED will light to indicate which computer is connected.
➎ (Optional) Connect the Micro USB Power Input port to a power source to support applications with higher power requirements.

Support and Documentation Notice

All information, documentation, firmware, software utilities, and specifications contained in this package are subject to change without prior notification bythe manufacturer.
To reduce the environmental impact of our products, ATEN documentation and software can be found online at http://www.aten.com/download/

Technical Support

www.aten.com/support

Scan for more information

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT:

This equipment has been tested and found to comply with the limits for a Class B digital service, pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation. Any changes or modifications made to this equipment may void the user s authority to operate this equipment. This equipment generates, uses, and can radiate radio frequency energy. f not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna;
– Increase the separction between the equipment and receiver;
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected;
– Consult the dealer/an experienced radio/television technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>