ROBB ROB-100-006-0 Z-Wave RGBW Remote Control Instruction Manual

: June 12, 2024
: ROBB

Table of Contents

ROBB ROB-100-006-0 Z-Wave RGBW Remote Control
Product Information
Function introduction
Safety & Warnings
Quick Start
Product Description
Operating the device
Technical Data
SUPPORTED COMMAND CLASS
Installation
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ROBB ROB-100-006-0 Z-Wave RGBW Remote Control

Product Information

Product Name: Z-Wave RGBW Remote Control
Model Number: ROB_100-006-0
Battery: CR2450
Z-Wave Frequency: 868.42MHz
Power Supply: 3VDC (1xCR2450 battery)
Operating Temperature: Not specified
Relative Humidity: Not specified
Dimensions: 71.20mm x 55.57mm x 11mm
Waterproof Grade: IP20
Encryption Modes Supported: S0, S2 Authenticated, S2 Unauthenticated
Product Usage Instructions

Function introduction

ROBB ROB-100-006-0 Z-Wave RGBW Remote Control fig-1

Product Data

Z-Wave Frequency	868.42MHz
Power Supply	3VDC(1xCR2450 battery)
Operating temperature	0 to 40°C
Relative humidity	8% to 80%
Dimensions	71.2×71.2×13.6mm
Waterproof Grade	IP20

Safety & Warnings

This device contains a button lithium battery that shall be stored and disposed of properly.
DO NOT expose the device to moisture.

Quick Start

How to install:

Step 1: turn on your remote control.
Step 2: activate inclusion mode on your Z-Wave controller.
Step 3: activate the inclusion mode of your remote control by pressing and holding down both buttons and of Group 2 together over 3 seconds.

Product Description

The remote control is a Z-Wave device that can both control other Z-Wave devices and activate scenes in Gateways. Although it is controlling other devices, the device cannot act as Z-Wave network controller (primary or secondary) and will always need a Z-Wave network controller to be included into a Z-Wave network. It also supports the Over The Air (OTA) feature for the product’s firmware upgrade.
The remote control has the following functions:

Control of groups of other Z-Wave devices using ‘ON’, ‘OFF’, Dim and RGB color control commands.
Activation of scenes in Gateway mode.

The encryption modes that the remote control supports are S0, S2 Authenticated, S2 Unauthenticated. When the remote control is being included into a Z-Wave network, you can use your primary controller/gateway to enable one encryption mode or disable encryption. (The primary controller/gateway shall support encryption mode configuration).

Installation Guide
Please read carefully the enclosed user manual before installation of remote control, in order to ensure an error-free functioning.
The remote control unit is supplied as a complete set for flush mounting in the standard circular European wall boxes with 60mm diameter.

Exclusion (Removing from a Z-Wave network)
There are two exclusion methods:
Method 1: Exclusion from the primary controller/gateway as follows:

Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers manual on how to set your controller into exclusion).
Press and hold down both buttons and of Group 2 over 3 seconds, LED indicator turns on, the remote control will be set to exclusion mode, and waiting to be excluded, after 7s LED indicator blinks 4 times quickly to indicate successful exclusion.

Method 2: Factory reset the remote control will force the remote control to be excluded from a network. (please refer to the part “Factory Reset” of this manual)
Note: Factory reset is not recommended for exclusion, please use this procedure only if the primary controller/gateway is missing or otherwise inoperable.

How to check whether the remote control already included to a network
Short press any button, if LED indicator blinks 3 times, the remote control does not belong to any network, if LED indicator turns on, it means the remote control has already been included to a network.
If the remote control already belongs to a network, follow the exclusion process before including it in your network. Otherwise, inclusion of this device will fail.

Inclusion (Adding to a Z-Wave network)

Make sure the remote control does not belong to any Z-Wave network. Short press any button. If the LED indicator does not turn on, the remote control does not belong to any network. Proceed to step 2. If the LED indicator turns on, it means the remote control has already been included in a network. In this case, set the remote control to exclusion mode (refer to the part Exclusion of this manual) and then proceed to step 2.
Set the primary controller/gateway into inclusion mode. Refer to your primary controller’s manual for instructions on how to turn it into inclusion mode.

Factory Reset
Press and hold down both buttons of Group 2 together for over 10 seconds, LED indicator turns on and then blinks 4 times quickly to indicate successful factory reset.

Association
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed). In case the event happens all devices stored in the respective association group will receive a common wireless command.

Association Groups:
Each group supports maximum 5 nodes for association, the same device can be associated with multiple groups on the remote control simultaneously, to ensure better control experience, the remote control shall remove the associated devices that are not under working status from association groups in time.

Association Groups	Group Name	Max Nodes	Description

Group 1

|

Lifeline

|

5

| 1. Send Command Class “Device Reset Locally Notification V1” to associated devices of this group to report factory reset information when factory reset the remote control.

2. When the remote control battery power value changes, send Command Class “Battery Report V1” to associated devices of this group to report power value information.

3. Short press or press and hold down any button to send scene activation command to the associated devices of this group using Command Class “Central Scene Notification V3”

Group 2

|

Launch 1

|

5

| • Short press button to send ON/OFF command to associated devices of this group using Command Class “Basic Set V2”.

• Press and hold down the button to send light intensity increase/decrease command to associated devices of this group using Command Class “Multilevel V4”.

• Short press W/ button of Group 2, turn on/off white/RGB channel of associated devices of this group using the Command Class “Color Switch Set”.

• Press and hold down W/ button of Group 2, adjust the intensity of the white/RGB channel of associated devices of this group using the Command Class “Color Switch Start Level Change”.

Set and unset associations:
(Note: All association information will be cleared automatically once the remote control is excluded from a network.)
There are two methods to set associations:

Set association by operating the primary controller/gateway to send association command to the remote control:
When set the association from the primary controller/gateway, the remote control shall be activated first, if it is not activated, you should activate it manually.
The primary controller/gateway sends association commands to the remote control using “Command Class ASSOCIATION” or “Command Class Multi Channel Association”
Set association by operating the remote control and devices to be controlled:
To control a Z-Wave device from the remote control the node ID of this device needs to be assigned to one of the two association groups.

This is a three-step process:

Press and hold down both buttons of Group 2 over 3 seconds, LED indicator turns on.
Short press button within 7s to associate the device to this group, short press to remove the association of the device from this group.
Operate the device to be controlled to send Node Information Frame (please refer to the device manual) within 10 seconds, or set the device to exclusion mode within 10 seconds, since it will send Node Information Frame in exclusion mode, LED indications are as follows:
LED blinks twice to indicate that the remote control failed to add the associated device (the association group has already added the maximum quantity of associated devices that it supports ).

LED blinks 5 times to indicate that the remote control added the associated device successfully. LED blinks 8 times to indicate that the remote control removed the associated device successfully.
To remove all associated devices in an association group on the remote control directly:

Press and hold down both buttons and of Group 2 over 3 seconds, LED indicator turns on.
Click button on the remote control 5 times continuously within 7 seconds to remove all associated devices of this group, LED indicator blinks 8 times to indicate that the associated devices are removed successfully.

Operating the device

ROBB ROB-100-006-0 Z-Wave RGBW Remote Control fig-4

Short press the button of Group 2, send ON/OFF command to all associated devices of Association Group 2.
Press and hold down button of Group 2, send light intensity increase/decrease command to all associated devices of Association Group 2.
Short press W button of Group 2, send Color Switch Set commands to all associated devices of Association Group 2.
Press and hold down W button of Group 2, send Color Switch Start Level Change commands to all associated devices of Association Group 2.
Short press button of Group 2, send Color Switch Set commands to all associated devices of Association Group 2.
Press and hold down button of Group 2, send Color Switch Start Level Change commands to all associated devices of Association Group 2.
Short press/press and hold any button to send scene activation command to association group 1 using Command Class “Central Scene Notification V3”.

How to communicate with the device
The remote control is under sleepy mode for most of the time to save battery power. It can not receive wireless command under sleepy mode. Before the gateway interacts data with the remote, the remote control shall be activated manually first. Short press any button to activate the remote control for 3s, and press and hold down buttons of Group 2 together over 1 second to activate the remote control for 7s.

Node Information Frame
The Node Information Frame is the business card of a Z-Wave device. It contains information about the device type and the technical capabilities. The inclusion and exclusion of the device is confirmed by sending out a Node Information Frame. Beside this it may be needed for certain network operations to send out a Node Information Frame.

How to send out Node Information Frame:
Set the wall controller into inclusion/exclusion mode: Press and hold down both and over 3 seconds, LED indicator turns on to indicate the wall controller has already sent out Node Information Frame, the user can repeat the operation to set the wall controller to quit “inclusion/exclusion mode”.

Technical Data

Battery Type	1*CR2450
Frequency	868.42 MHz
Wireless Range	up to 100 m outside, on average up to 20 m inside buildings
SDK	6.71.01
Explorer Frame Support	Yes
Device Type	Wall Controller
Generic Device Class	Switch Remote
Specific Device Class	Switch Remote Multilevel
Routing	No
FLiRS	No

Z-Wave Plus Info

Parameter	Value
Z-Wave Plus Version	1
Role Type	Slave Portable
Node Type	ZWAVEPLUS
Installer Icon Type	0x0b00 (ICON_TYPE_GENERIC_REMOTE_CONTROL_SIMPLE)
User Icon Type	0x0b00 (ICON_TYPE_GENERIC_REMOTE_CONTROL_SIMPLE)