ROBB 200-006-0 Zigbee LED Dimmer Instruction Manual
- June 5, 2024
- ROBB
Table of Contents
Zigbee LED Dimmer
Important: Read All Instructions Prior to Installation
**Function introduction
**
Operation
- Do wiring according to the connection diagram correctly.
- This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
- Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network) Step 1: Remove the device from the previous Zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part “Factory Reset Manually”.
Step 2: From your ZigBee Controller or hub interface, choose to add a lighting device and enter Pairing mode as instructed by the controller.
Step 3: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15 seconds timeout, and repeat the operation.
4. TouchLink to a Zigbee Remote
Step 1: Method 1: Short press “Prog” button (or re-power on the device) 4
times to start Touchlink commissioning immediately, 180S timeout, repeat the
operation.
Method 2: Re-power on the device, Touchlink commissioning will start after 15S
if it’s not added to a zigbee network, 165S timeout. Or start immediately if
it’s already added to a network, 180S timeout. Once timeout, repeat the
operation.
Note:
- Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
- TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
- For Hue Bridge & Amazon Echo Plus, add remote and device to the network first then TouchLink.
- After TouchLink, the device can be controlled by the linked remotes.
5. Removed from a Zigbee Network through Coordinator or Hub
Interface
6. Factory Reset Manually
Step 1: Short press “Prog.” key for 5 times continuously or re-power on the
device for 5 times continuously if the “Prog.” key is not accessible. 
Note
- If the device is already at the factory default setting, there is no indication of when the factory reset again.
- All configuration parameters will be reset after the device is reset or removed from the network.
7. Factory Reset through a Zigbee Remote (Touch Reset)
Step 1: Re-power on the device to start TouchLink Commissioning, 180 seconds
timeout, and repeat the operation.
Note: Make sure the device is already added to a network, the remote is
added to the same one, or not added to any network.
8. Find and Bind Mode
Step 1: Short press the “Prog.” button 3 times (Or re-power on the device
(initiator node) 3 times) to start to Find and Bind mode (connected light
flashes slowly) to find and bind the target node, 180 seconds timeout, repeat
the operation.
9. Learning to a Zigbee Green Power Remote
Step 1: Short press the “Prog.” button 4 times (Or re-power on the device 4
times) to start Learning mode (connected light flashes twice), 180 seconds
timeout, and repeat the operation.
10. Delete Learning to a Zigbee Green Power Remote
Step 1: Short press “Prog.” button 3 times (Or re-power on the device 3 times)
to start delete Learning mode (connected light flashes slowly), 180 seconds
timeout, and repeat the operation.
11. Setup a Zigbee Network & Add Other Devices to the Network (No
Coordinator Required)
Step 1: Short press “Prog.” button 4 times (Or re-power on the device 4 times)
to enable the device to set up a ZigBee network (connected light flashes
twice) to discover and add other devices, 180 seconds timeout, repeat the
operation.
Step 2: Set another device or remote or touch panel into network pairing mode
and pair to the network, refer to their manuals.
Step 3: Pair more devices and remotes to the network as you would like, refer
to their manuals.
Step 4: Bind the added devices and remotes through Touchlink so that the
devices can be controlled by the remotes, refer to their manuals.
Note 1) Each added device can link and be controlled by max. 30 added
remotes.
2) Each added remote can link and control max. 30 added devices.
12. ZigBee Clusters the device supports are as follows:
Input Clusters
- 0x0000: Basic
- 0x0003: Identify
- 0x0004: Groups
- 0x0005: Scenes
- 0x0006: On/off
- 0x0008: Level Control
- 0x0b05: Diagnostics
Output Clusters
- 0x0019: OTA
13. OTA
The device supports firmware updating through OTA, and will acquire new
firmware from zigbee controller or hub every 10 minutes automatically.
14. Controlled by a push switch:
Once connected with a push switch, click the push switch to switch ON/OFF,
press and hold down it to increase/decrease light intensity.
Product Dimension
Wiring Diagram
Product Data
No.| Input Voltage| Output Current| Output Power|
Remarks| Size(LxWxH)
---|---|---|---|---|---
1| 12-36VDC| I lx8A| lx(96-288)W| ‘Constant voltage’| 95x37x20mm
2| 12-36VDC| I lx350mA| 1x(4.2-12.6)W| ‘Constant current’| 95x37x20mm
3| 12-36VDC| I lx700mA| 1x(8.4-25.2)W| ‘Constant current’| 95x37x20mm
- ZigBee LED dimming light device based on the latest ZigBee 3.0 protocol
- Enables to control of ON/OFF and light intensity of connected LED lights
- ZigBee end device that supports Touchlink commissioning
- Can directly pair to a compatible ZigBee remote via Touchlink without a coordinator
- Supports self-forming ZigBee network without a coordinator
- Enables to add of devices to the self-formed Zigbee network
- Supports self-forming ZigBee network without a coordinator and add other devices to the network
- Supports find and bind mode to bind a ZigBee remote
- Supports ZigBee green power and can bind max. 20 Zigbee green power remotes
- Compatible with universal ZigBee gateway products
- Waterproof grade: IP20
Safety & Warnings
- DO NOT install with power applied to the device.
- DO NOT expose the device to moisture.
ROB 200-006-0
Documents / Resources
| ROBB
200-006-0 Zigbee LED
Dimmer
[pdf] Instruction Manual
200-006-0, Zigbee LED Dimmer, 200-006-0 Zigbee LED Dimmer
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>