ROBB SMARRT SRP-ZG9105-12-50CVT CW50W ZigBee CCT LED Driver Constant Voltage Instructions

: June 12, 2024
: ROBB SMARRT

Table of Contents

Read User Manual Online (PDF format)
Download This Manual (PDF format)

ROBB SMARRT SRP-ZG9105-12-50CVT CW50W ZigBee CCT LED Driver

 **Constant Voltage Instructions**

Important : Read All Instructions Prior to Installation

Function introduction

Product Data

Dimmable LED driver for tunable white
ZigBee CCT LED light device based on ZigBee 3.0 protocol
Max. output power 50W total
2 channels 12/24V DC constant voltage output
Class Ⅱ power supply, full isolated plastic case
High power factor and efficiency
Deep and smooth dimming to 0.1%
Suitable for indoor LED lighting applications
Enables to control ON/OFF, light intensity and CCT of connected CCT LED lights
ZigBee end device that supports Touchlink commissioning
Can directly pair to a compatible ZigBee remote via Touchlink
Supports find and bind mode to bind a ZigBee remote
Supports zigbee green power and can bind max. 20 zigbee green power remotes
Compatible with universal ZigBee gateway products
Compatible with universal CCT ZigBee remotes
Waterproof grade: IP20
5 years warranty

Safety & Warnings

DO NOT install with power applied to device.
DO NOT expose the device to moisture.

Wiring Diagram

Operation

Do wiring according to connection diagram correctly.
This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)

Step 1 : Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part “Factory Reset Manually”.
Step 2 : From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller.
Step 3 : Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15 seconds timeout, repeat the operation.

4. TouchLink to a Zigbee Remote

Step 1: Method 1 : Short press “Prog” button (or re-power on the device) 4 times to start Touchlink commissioning immediately, 180S timeout, repeat the operation.
Method 2: Re-power on the device, Touchlink commissioning will start after 15S if it’s not added to a zigbee network, 165S timeout. Or start immediately if it’s already added to a network, 180S timeout. Once timeout, repeat the operation.

Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.
4) After TouchLink, the device can be controlled by the linked remotes.

5. Removed from a Zigbee Network through Coordinator or Hub Interface

6. Factory Reset Manually

Step 1 : Short press “Prog.” key for 5 times continuously or re-power on the device for 5 times continuously if the “Prog.” key is not accessible.

Note: 1) If the device is already at factory default setting, there is no indication when factory reset again .
2) All configuration parameters will be reset after the device is reset or removed from the network.

7. Factory Reset through a Zigbee Remote (Touch Reset)

Note : Make sure the device already added to a network, the remote added to the same one or not added to any network.

Step 1: Re-power on the device to start TouchLink Commissioning, 180 seconds timeout, repeat the operation.

8. Find and Bind Mode

Step 1: Short press “Prog.” button 3 times (Or re-power on the device (initiator node) 3 times) to start Find and Bind mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the operation.

9. Learning to a Zigbee Green Power Remote

Step 1 : Short press “Prog.” button 4 times (Or re-power on the device 4 times) to start Learning mode (connected light flashes twice), 180 seconds timeout, repeat the operation.

10. Delete Learning to a Zigbee Green Power Remote

Step 1: Short press “Prog.” button 3 times (Or re-power on the device 3 times) to start delete Learning mode (connected light flashes slowly), 180 seconds timeout, repeat the operation.

11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required)

Step 1 : Short press “Prog.” button 4 times (Or re-power on the device 4 times) to enable the device to setup a zigbee network (connected light flashes twice) to discover and add other devices, 180 seconds timeout, repeat the operation.

12. ZigBee Clusters the device supports are as follows:

Input Clusters