ROBB 70110005 Zigbee Smart Plug Instruction Manual
- June 12, 2024
- ROBB
Table of Contents
Zigbee Smart Plug
Important: Read All Instructions Prior to Installation
Function introduction
Product Data
| Zigbee profile | 0x0104(ZHA) |
|---|---|
| Device ID | 0x000A(Plug-in Unit) |
| Radio Frequency | 2.4GHz |
| Input Voltage | AC200-240V, 50/60Hz |
| Max. Load | 16A |
| Over Current Protection | 16.1A |
| Operating temperature | 0 to 40°C |
| Relative humidity | 8% to 80% |
| Dimensions | 114.8×54.8×74.7(mm) |
| LED Indicator State | Definition (16.1A Over Current) |
| --- | --- |
| Flashes red slowly | Over current |
| Stays solid orange | Load power > 2200W |
| Stays solid yellow | Load power 2001-2200W |
| Stays solid green | Load power 1501-2000W |
| Stays solid cyan | Load power 1001-1500W |
| Stays solid blue | Load power <= 1000W |
| Flashes purple slowly | Firmware updating via OTA |
| Stays solid white at a low brightness | Load switched off |
- ZigBee smart plug based on latest ZigBee 3.0 protocol
- Enables to control ON/OFF of the load, supports max. 16 scenes
- ZigBee end device that supports Touchlink commissioning
- Supports find and bind mode to bind a ZigBee remote
- Supports zigbee green power and can bind max. 20 zigbee green power switches
- Supports temperature measurement
- Supports over current protection and power metering, enables to report power consumption to gateway
- Waterproof grade: IP20
Safety & Warnings
- DO NOT install with power applied to device.
- DO NOT expose the device to moisture.
Operation
1. Plug the smart plug into AC power source.
2. This ZigBee device is a wireless receiver that communicates with a
variety of ZigBee compatible systems. This receiver receives and is controlled
by wireless radio signals from the compatible ZigBee system.
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee
Network)
Step 1: Remove the device from previous zigbee network if it has already
been added to, otherwise pairing will fail. Please refer to the part “Factory
Reset Manually”.
Step 2: From your ZigBee Controller or hub interface, choose to add
lighting device and enter Pairing mode as instructed by the controller.
Step 3: Short press “Program” button 5 times continuously to set the
device to network pairing mode, LED indicator will flash white fast.
4. TouchLink to a Zigbee Remote
Step 1: Short press “Prog” button 4 times (Or re-power on the device 4
times) to start Touchlink commissioning, 180S timeout. Once timeout, repeat
the operation.
Note:
- Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
- TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
- To control by both gateway and remote, add remote and device to network first then TouchLink.
- After TouchLink, the device can be controlled by the linked remotes.
5. Removed from a Zigbee Network through Coordinator or Hub Interface
6. Factory Reset Manually
Step 1: Short press the “program” button 5 times continuously, the plug
will enter into network pairing mode.
7. Factory Reset through a Zigbee Remote (Touch Reset)
Note: Make sure the device already added to a network, the remote added
to the same one or not added to any network.
Step 1: Re-power on the device to start TouchLink Commissioning, 180
seconds timeout, repeat the operation.
8. Find and Bind Mode
Step 1: Short press “Prog.” button 3 times to start Find and Bind mode
(LED indicator flashes white slowly) to find and bind target node, 180 seconds
timeout, repeat the operation.
Note: Make sure both the device and remote are added to the same gateway
that supports find and bind.
9. Learning to a Zigbee Green Power Switch
Step 1: Short press “Program” button 4 times to start Learning to GP
switch mode (LED indicator flashes twice), 180 seconds timeout, repeat the
operation.
10. Delete Learning to a Zigbee Green Power Switch
Step 1: Short press “Program” button 3 times to start delete Learning to
GP switch mode (LED indicator flashes slowly), 180 seconds timeout, repeat the
operation.
11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator
Required)
Step 1: Short press “Program” button 4 times to enable the device to
setup a zigbee network (LED indicator flashes white twice) to discover and add
other devices, 180 seconds timeout, repeat the operation.
Step 2: Set another device or remote or touch panel into network pairing
mode and pair to the network, refer to their manuals.
Step 3: Pair more devices and remotes to the network as you would like,
refer to their manuals.
Step 4: Bind the added devices and remotes through Touchlink so that the
devices can be controlled by the remotes, refer to their manuals.
Note:
- Each added device can link and be controlled by max. 30 added remotes.
- Each added remote can link and control max. 30 added devices.
12. ZigBee Clusters the device supports are as follows:
Input Clusters
- 0x0000: Basic
- 0x0003: Identify
- 0x0004: Groups
- 0x0005: Scenes
- 0x0006: On/off
- 0x0702: Simple Metering
- 0x0b04: Electrical Measurement
- 0x0b05: Diagnostics
- 0x1000: ZLL Commissioning
- 0x0402: temperature measurement
Output Clusters
- 0x0003: Identify
- 0x0019: OTA
13. OTA
The device supports firmware updating through OTA, and will acquire new
firmware from zigbee controller or hub every 10 minutes automatically.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>