VIVO MOUNT-VW03G Silver Pneumatic Arm TV Wall Mount Instruction Manual
- June 12, 2024
- Vivo
Table of Contents
Silver Pneumatic Arm TV Wall Mount
Instruction Manual
MOUNT-VW03G Silver Pneumatic Arm TV Wall Mount
SKU: MOUNT-VW03G
https://vivo-us.com/products/mount-vw03g
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com| www.vivo-us.com
Chat live with an agent!| 309-278-5303
---|---|---
| |
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity.
We cannot be liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
PACKAGE CONTENTS
NOTE: NOT ALL
HARDWARE INCLUDED WILL BE USED
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD
STUDS TO MOUNT.
We include mounting for brick and concrete walls. If unsure, please contact us
at vivo-us.com, email at help@vivo-us.com, or call us at
309-278-9303.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
TOOLS NEEDED
ASSEMBLY STEPS
STEP 1
Remove VESA plate from the Mount (A) by removing two bottom nuts with Wrench
(T-C) and loosening top two nuts. The plate will lift out from the slots on
the top of the **bracket. STEP 2
OPTION A: Wood Wall
Use Mount (A) to mark mounting holes on wall where stud is located. Use Bubble Level (T-D) to ensure mount is level. Using a 3/16” drill bit, drill holes at least 2.2” deep into marked locations. Insert ST6.3×5.5mm Screw (W-A) into top hole, leaving 3mm of thread exposed. Hang top hole in mount over the bolt, and secure using two more ST6.3×5.5mm Screws (W-A) with Washers (W-C). Tighten all screws.
NOTE: Do not use concrete
anchors (W-B) with wood studs.
OPTION B: Concrete/Brick Wall
Use Mount (A) to mark mounting holes on wall. Use Bubble Level (T-D) to ensure mount is level. Using a 3/8” drill bit, drill holes at least 2.4” deep into marked locations. Press Anchors (W-B) into holes, then insert ST6.3×5.5mm Screw (W-A) into top hole, leaving 3mm of thread exposed. Hang top hole in mount over the bolt, and secure using two more ST6.3×5.5mm Screws (W-A) with Washers (W-C).
Tighten all screws.
STEP 3
Attach Covers (B) to Mount (A).
STEP 4
Secure VESA Adapters (D, E) to VESA Plate using M6x8mm Screws (S-A) in the appropriate configuration to match your televisions mounting holes.
NOTE: VESA adapters are not required for VESA patterns 200mm and smaller.
STEP 5
Attach VESA plate assembly to back of monitor using the appropriate Screws (M-C, M-B) for your monitor and D8 Washers (M-E).
For curved monitors, use Screws (M-C, M-D) with M8
Washers (M-E) and Spacers (M-F, M-G).
STEP 6**
Attach VESA plate with monitor to Mount (A) using previously remove nuts and Wrench (H) as shown in diagram.
Adjust as Desired
To adjust gas spring lift strength, turn the screw on the top of the center
joint using the 6mm Allen Wrench (T-B). Clockwise will reduce strength, and
counter-clockwise will increase (screw turns most easily when arm is facing
straight forward). If the screw is difficult to access, remove the plastic arm
covers by rocking them up and down until they pop off. Adjust tilt joint using
the 4mm Allen Wrench (T-A). Organize cables using the built-in cable
management clips.
NOTE: If the mount makes a popping noise when raising or lowering,
tighten the socket set screw on top of the adjustment screw using a large
flat-blade screwdriver. 
WARNING:
Monitor must be installed on mount before making tension adjustments to the
gas spring arm.
Keep monitor in a straight orientation when making adjustments. 
Love your new VIVO setup and
want to share?
Tag us in your photo! @vivo_us
LAST UPDATED: 02/07/2023
REV1.1 Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
| 309-278-5303| AVG. RESOLUTION TIME
(within office hrs): 5M 4S
---|---|---
| www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
| help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT:
www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Silver Pneumatic Arm Wall Mount for 40" to 70" TVs – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>