3 Legged Thing Alan 2.0 Professional Monopod Instruction Manual
- June 12, 2024
- 3 Legged Thing
Table of Contents
3 Legged Thing Alan 2.0 Professional Monopod
Look at the end of your box. See that little sticker with a serial number
and a barcode? Peel it off and put it here for safe keeping.
Or don’t.
IMPORTANT
DO NOT USE YOUR MONOPOD UNTIL YOU HAVE READ THESE INSTRUCTIONS. NO WARRANTY CLAIM WILL BE ENTERED INTO FOR THE MISUSE OR INCORRECT USE OF THESE PRODUCTS.
ANATOMY OF A MONOPOD
- Retractable Screw Mount
- Tri-Mount Plate
- Big Grip
- Leg Sections
- Twist Locks
- Boot/Footwear
Always hold your camera when removing it from the monopod!
Using The Monopod
To open and extend the monopod simply grip the twist locks (5) in your hand,
quarter turn, loosening the monopod allowing you to select a desired height.
Once the required height has been obtained lock the monopod in place by
rotating back to the original position, which will fully engage the leg lock.
The twist locks do not require to be undone further than a half turn, unless
you intend to completely disassemble the monopod for cleaning.
To attach your camera, billhead, or accessory, insert the mounting screw (1)
into the base of your camera. If your camera has a 1/”-20 thread, retract the
spring-loaded sleeve on the screw to reveal the smaller thread, then insert
into the base of your camera. Turn the monopod until the screw meets
resistance. Do not over-tighten.
The Tri-Mount Plate comes with three hollow ends (a), for connecting your strap or carabiner, and one 3/8” threaded screw in the centre. The outer part can be retracted to reveal the 1/4” thread in the centre.
ANATOMY OF DOCZ
- Dual 1/4”-20 mount with 3/8”- 16 adapter sleeve
- Screw Lock
- Ball
- Legs
- Leg Buttons
- Rubber Boot / Ball Adjuster
Using Docz
To open the legs from folded, pull down until they click into place. To fold
them back up, press the button (5) at the base of each leg and fold upwards.
To attach to a monopod unscrew the rubber Boot and the adapter in the base of
the monopod. If this adapter is stuck, you can remove this by using tools, or
a coin, and turn it anti-clockwise. Put the adapter somewhere safe!
Once removed, insert Docz’ orange screw thread (1) into the base of the
monopod and turn until the screw meets resistance. If you want to adjust the
ball position, turn the orange screw lock (2) upwards until it meets the base
of the monopod. To adjust the ball (3) position, loosen the rubber Boot (6) on
the base of Docz. Angle the monopod to the desired position. Tighten the Boot
(6) to lock the ball into place.
Cleaning
It is advised that you wash your monopod after using it in sand, or dirt.
For videos on how to clean your 3 Legged Thing products, please visit:
https://www.3leggedthing.com/faq
Never use WD40 on your monopod as it can be a solvent. Always use silicone
grease.
Warranty Information
Your 3LT product comes with a 5 Year Global Warranty. On the box you will find
a sticker with a unique barcode and serial number. Use this serial number to
register your products at
www.3leggedthing.com/register.
Details of your warranty can be found at
www.3leggedthing.com.
Your warranty covers 3 Legged Thing products only.
If you have a question or suspect you have a fault, contact us first at
support@3leggedthing.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>