HOLLYLAND Cosmo C1 SDI-HDMI Wireless Video Transmission System User Guide
- June 12, 2024
- HOLLYLAND
Table of Contents
Cosmo C1 SDI-HDMI Wireless Video Transmission System
User Guide
For the latest and detailed user guide, please download it from the official website: www.hollyland-tech.comisupportiDownload
TYPICAL SETUP
Note: The transmitter
can be equipped with mushroom antenna. When there is a large height difference
between the transmitter and receiver, it is recommended to use Hollyland
mushroom antenna at the transmitter to improve the stability of wireless
transmission.
PRODUCT INTERFACES
A . TRANSMITTER
| 1 | Antenna Interface |
|---|---|
| 2 | HDMI Input |
| 3 | SDI Input |
| 4 | SDI Loop out |
| 5 | DC Power Input |
| 6 | Expansion Accessories Mounting Hole |
| 7 | LED Light (Yellow light indicates connection status, red ight indcatos low |
power)
8| OLED Screen
9| Thumbwheel Switch
10| Power Switch
11| USB Type-C Interface
12| Outlet
13| 1/4 Threaded hole
B. RECEIVER
| 1 | Antenna interface |
|---|---|
| 2 | HoMIOutput |
| 3 | SDIOutputt |
| 4 | sDIOutput2 |
| 5 | DG Power Input |
| 6 | Expansion Accessories Mounting Hole |
| 7 | LED Light (Yellow light indicates connection satus, red ight indcatos low |
power)
8| OLED Screen
9| Thumbwheel Switch
10| Power Switch
11| USB Type-CInterface
12| Outlet
13| 1/4 Threaded Hole
INTALLATION
INSTALLATION OF TRANSMITTER
- Installthe antenna according to the angle shown n the picture.
- Install the magic arm onto the 1/4 threaded hole of the transmitter and installthe assembled transmitter into the camera body
- Install the battery (compatible with NP-F970 and others of same series).
- Push the power switch to turm on the device.
INSTALLATION OF RECEIVER
- Installthe antenna according to the angle shown n the picture.
- Install the receiver onto the stent through the 1/4 threaded hole on the bottom ofthe device.
- Install the battery (compatible with NP-F970 and others of same series).
- Push the power switch to turm on the device.
OLED DISPLAY
signal Strength- Indicator of Power Supply
- video Format
- Ghannel Display
- Indicator of Auto-frequency-hopping
NOTE
The “AUTO” indicates that the frequency point is in the automatic frequency
hopping mode (the picture on the right); switch the frequency manually will
change the device to the locked-frequency-mode state in the left pcture.
QUICK GUIDE
ENTER MENU
Long press the thumbwheel switch for three saconds to enter the menu. Flip the
toggle ‘wheel up or down to switch menu options, and click to confirm.
CHANNEL SWITCHING
Toggle up/down the switcher to change the menu options on the transmiter or
receiver, lick the confirm key o confirm the channel, then the receiver and
the ransmitter channel will be synchronized automatcally.
SUPPORT
IT encounter any problems in using the product or need any help, please follow
these ways 10 get more technical support
Hollyland Products User Group
HollylandTech
HollylandTech
support@holyland-tech.com
hollylanctech.com
FCC REQUIREMENT
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authorty o operate the equipment.
“This device complies with Part 15 of the FCC Rules. Operation is subject 10
the following two condions:
- This devico may not cause harmful nterference, and
- this device must accept any interference recsived, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limis for a
Class B digtal device, pursuant to Part 15 of the FCC Rules. These imits are
designed to provide reasonable protection against harmful interference in a
residential installaion. This equipment genorates, usos, and can radiato radio
frequency energy, and f not installed and used In accordanco with the
instructons, may cause harmiul interference to radio communications. However,
there is no quarantee that interforence will not occur in a partcular
instalaton. If this equipment does cause harmiul inerference to radio or
television reception, which can be determined by tuming the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the folowing measures:
~ Reorient or relocate the receiving antenna.
~ Increas the separation betwoen the equipment and receiver.
— Connect the equipment into an outet on a circut diferent from that 1o which
the recsiver is connected.
~ Consult the dealer or an experienced radio/TV technician for help.
“This equipment complies with FCC radiation oxposuro limis sat foth for an
uncontrolied environment. This equipment snould be instaled and operated with
a minimum distance of 200m between the radiator & your body. This transmitter
must not be cocated or operating in conjunction with any other antenna or
transmiter, 1 any interference received, including interference that may cause
undesired operation.
WWW.HOLLYLAND-TECH.COM
WIRELESS VIDEO TRANSMISSION SYSTEM
Hollyland Products User Group
HollylandTech
HollylandTech
support@holyland-tech.com
hollylanctech.com
‘SHENZHEN HOLLYLAND TECHNOLOGY CO,. LTD
8. 50 Building, Skywort Inovation Valey, Tangtou, Shiyan, Baoan District
Shenzhan, China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>