CRYSTORAMA KEN-8300-VG-BF Kendal Six Light Ceiling Mount Instruction Manual
- June 12, 2024
- CRYSTORAMA
Table of Contents
CRYSTORAMA KEN-8300-VG-BF Kendal Six Light Ceiling Mount
Product Information
The Crystorama KEN-8300-VG-BF is a lighting fixture that has been providing lighting solutions for sixty years. This product has a damp rating, which means that it can be used in areas with high humidity levels. The product comes with a mounting plate, canopy, center tube, glass panels, glass diffusers, metal hood, socket, and other mounting hardware. It requires 6 candelabra base bulbs with a recommended wattage of 40 Watts and a maximum wattage of 60 Watts. LED bulbs are recommended for extended use.
The product dimensions are as follows: W5-7/8”xH7/8” for the canopy, D1”xL2-3/8” for the center tube, 2-1/8” for the glass panel, 7-7/8” for the glass diffuser, and 7-3/4”x29-1/4” for the metal hood. It is important to note that all electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes. The product may contain lead, which is known to the state of California to cause cancer and/or birth defects or reproductive harm.
Product Usage Instructions
- Turn off the power to all electrical components before installation.
- Slip the center tube assembly along wire and thread onto the nipple located on the top of the light cluster.
- Slide the glass diffuser onto the bottom of metal frame and secure it with clips.
- Slide the glass panels inside the metal frame and secure it with clips.
- Install the mounting plate to outlet box using two outlet box screws.
- Install canopy onto the mounting plate, and secure it with the screws.
- Install the bulb(not included) into the socket.
- Hang the metal hood over the bracket by inserting the hook into the hole of bracket. Please make sure the metal hood is safely secured.
To change the bulb, raise the metal hood up over the bracket and turn it sideway to take it down. Install the new bulb and put the metal hood back. It is recommended to use LED bulbs for extended use. If you have any doubts or concerns about installation or usage, please consult a licensed electrician.
WARNING
- Electrical Danger
- Turn Power off
All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes.
You will need
- You will need 6- Candelabra Base Bulb 40 Watts Frosted bulb Recommended 60 Watts Max.
- USE LED BULBS FOR EXTENDED USE
- This fixture is Damp rated
How to install
- Slip the center tube assembly along wire and thread onto the nipple located on the top of the light cluster.
- Slide the glass diffuser onto the bottom of metal frame and secure it with clips.
- Slide the glass panels inside the metal frame and secure it with clips.
- Install the mounting plate to outlet box using two outlet box screws.
- Install canopy onto the mounting plate, and secure with the screws.
- Install the bulb (not included) into the socket.
- Hang the metal hood over the bracket by inserting the hook into the hole of bracket. Please make sure the metal hood is safely secured.
How to change the bulb
- Raise the metal hood up over the bracket and turn it sideway to take it down. Install the new bulb and put the metal hood back.
Dimension
Part Numbers
- A. (1)-Mounting hardware
- B. (1)-Mounting plate
- C. (2)-Mounting screw
- D. (1)-Canopy W5-7/8″XH7/8′ #XRF8300VGBFCAN5.875IN
- E. (1)-Center tube D1″xL2-3/8′ #XRF8300VGBFSTEN2.375IN
- F. (9)-Glass panel #XRF8300GLA2.125IN
- G. (3)-Glass diffuser #XRF8300DIFF7.875IN
- H. (3)-Metal hood
- I. (6)-Socket
WARNING: This product can expose you to Lead which is known to the state of California to cause cancer and/or birth defects or reproductive harm. For more information go to www.P65Warnings.ca.gov
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>