BARRETTE OUTDOOR LIVING 34111484 Semi-Privacy Vinyl Fence Kit Instruction Manual
- June 6, 2024
- Barrette OUTDOOR LIVING
Table of Contents
BARRETTE OUTDOOR LIVING 34111484 Semi-Privacy Vinyl Fence Kit
WARNING:
- Improper installation of this product can result in personal injury. Always wear safety goggles when cutting, drilling and assembling the product.
- Incorrect installation may cause harm to the product or individual.
- Check local building codes to determine pool-safe fencing options.
NOTICE:
- DO NOT attempt to assemble the kit if parts are missing or damaged.
- DO NOT return the product to the store. For assistance or replacement parts call: 1-800-336-2383.
BEFORE YOU BEGIN
Check your local zoning laws.
- Local zoning laws and Home Owners Associations may regulate the location, style and height of your fence or even require a permit signoff beforehand.
- Check local codes for frost line depth and regulations.
- Additional products and assembly may be required to meet wind code requirements. Notice of acceptance (NOA) can be found at www.miamidade.gov/building/pc-search_app.asp Contact your local utilities companies.
- You must have the utility companies clearly mark your property for electrical, gas or water lines to avoid puncturing any unseen underground utilities.
TOOLS NEEDED
| Posts
---|---
| Post Tops
| Concrete
| Coarse Gravel (6″ per hole)
| Post Hole Digger/Shovel
| String Line Stakes with String
| Level
| Tape Measure
| Rubber Mallet
| Safety Glasses
| Glue
**Component list
**
Description
Rails
Boards
Pickets
Included depending on style.
To obtain and review a copy of the warranty please visit barretteoutdoorliving.com. You may also contact us at 1-800-336 2383 or email Cs.outdoorliving@ebarrette.com
-
Mark the fence location using string and line stakes (Fig. 1).
NOTE: Plan gate placement, opening and hardware clearance before installing fencing. -
Post Location:
Measure the width of the fence panel (X) plus the width of the post (Y). This is the common center-to-center measurement (unless there is a cut-down panel) for post hole location (Fig. 2).
Post Installation:
Dig first two post holes in diameter based on size chart below* and down to your specified frost line. Insert filler/gravel into the bottom of both holes and then set first post in post hole.
Add wet or dry concrete mix according to the manufacturer’s instruction to the top of the hole for first post only and level it.
Example: When your frost line is 36″ insert 12″
of gravel/ filler and 24″ of post with concrete surrounding (Fig. 3).
Diameters based on post size:
10″ for 5″ x 5″ post
8″ for 4″ x 4″ post
3. For Picket Panels:
-
a. Insert top and bottom rails into top and bottom post hole routes of both posts (Fig. 4).
b. Starting from the left side, insert pickets/boards down through the top rail. Finish by locking pickets/boards into bottom rail (Fig. 5).
NOTE: Scalloped and arched panels have pickets/ boards that are numbered. Start from left side with #1 picket/board first.
For Closed Top/Semi-Privacy Panels: -
a. Insert bottom rail into bottom post hole routes of both posts (Fig. 6).
NOTE: Some semi-privacy panels will have a middle rail. Insert the bottom and middle rails into the bottom and middle post hole routes of both posts. -
b. Starting from the left side, insert pickets/boards down into the bottom rail (Fig. 7).
NOTE: If panel has a middle rail, insert pickets/ boards down through the middle rail and then into the bottom rail. -
For Picket Panels:
Plumb and level second post and add concrete according to manufacturer’s instructions to top of post hole (Fig. 8).
For Closed Top/Semi-Privacy Panels:
Add top rail to pickets/boards working from left to right. Once top rail is engaged with all pickets/boards, snap top rail into both top post hole routes (Fig. 9). Plumb and level second post and add concrete according to manufacturer’s instructions to top of post hole. -
Check to ensure the second post is level, then add panel width plus one half (1⁄2) the width of your post. This will locate the center of your next hole. Then dig the third post hole accordingly (Fig. 10).
-
Repeat process from steps 2 to 5 until all fence panels and posts have been installed.
-
Apply glue on inside rim of post tops then attach to posts (Fig. 11).
Documents / Resources
|
BARRETTE OUTDOOR LIVING 34111484 Semi-Privacy Vinyl Fence
Kit
[pdf] Instruction Manual
34111484 Semi-Privacy Vinyl Fence Kit, 34111484, Semi-Privacy Vinyl Fence Kit
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>