LEIVI T181 Series Smart Toilet User Manual

LEIVI T181 Series Smart Toilet

Safety Precautions

To prevent damage to the unit and possible injury to users, please follow the safety warnings. Please be sure to carefully read through the user’s manual before installation. Keep the user’s manual after installation to refer to for troubleshooting advice.

Symbols And Meanings

WARNING

Could result in serious injury or death.

The following symbols are used to indicate important safety precautions when using the product.

| Prohibited.
---|---
| Pay close attention; caution.

WARNING

• It is not allowed to continue using if the product has some breakdown: Product heat abnormally;
• The product is smoking;
• The product has abnormal sound and smell;
• Product is leaking, broken or damaged;
• The toilet pan is blocked, etc.
• When the breakdown happens, if it do not handle in time and continues using, it might trigger problems like electric shock, injury, firing or water penetration inside the room, etc.
• Banana oil, gasoline, putty-powder, nylon brush or other (non-neutral) detergent is not allowed to clean the plastic parts like toilet seat cover, otherwise it might trigger chemical reaction or leakage, damage the product and cause people injury.
• Loosen electric outlet is not allowed as it might trigger electric shock or firing.
• It is not allowed to pull out and plug in the electric plug by wet hand as it might trigger electric shock or firing.
• It is not allowed to touch the electric plug when it is thundering and lighting as it might trigger electric shock.

Prohibited

• It is not allowed to use another electric resource, the load of using electric outlet could not be too big, as it might trigger firing due to over-heat.
• Detergent, water, wash detergent or urine is not allowed to spot into body and electric outlet, as it might trigger electric shock or firing.
• It is not allowed to let child stand or put heavy goods on the seat and cover, toilet pan or seat body, heavy hitting or knocking is not allowed.
• It is not allowed to disassemble, repair this product, (it must go for professional repair person service if it is necessary to repair), otherwise, it might cause damage to this product.
• Do not randomly damage the electric plug and electric line, if the electric line, electric plug is damaged, please do not use it any longer or repairby oneself, it must be repaired by a professional person, otherwise, it might trigger short-circuit, electric shock, firing.
• If the power cord is not long enough, please do not use a extension cord.
• The stove or lighted cigarette is not allowed to be placed next to the toilet pan, cigarette butt etc is not allowed to be thrown into toilet pan.
• Do not block the airopenings of the product. Keep the air openings free of lint, hair, and the like.
• Do not use while bathing.

WARNING

• When using in shower room, please install air exchange equipment to ensure the air in the shower room not too moist. This product is an electric products, it is not allowed to install it in the place that is easy high wet, easy split by water, otherwise it might trigger electric shock or fire.
• Please ensure to cut off the electric power before washing this product, do not use water to directly wash this product, otherwise it might trigger the electric shock or fire.
• Please put and use this product in the shadow, must not put directly beneath the sun, otherwise, it might cause the colorfading, or burn the surface of product due to the instability of the temperature.
• Do not use industrial water, wastewater, seawater, reclaimed water and other sewage, otherwise it may cause skin inflammation and other problems.
• Persons (including children) with physical, perceptual, intellectual disabilities or lack of experience and common sense need to use the product under the guidance or supervision of someone else, or they may cause electric shock, injury or fire.
• Please notice the assembly location of electric wiring plug, electric plug should be the water-proof plug. Assembly location of electric plug must be over 0.5m( 19.7in) above the floor, and far away from shower, bathtub, otherwise it might cause electricity leakage.

Caution

• When installing this product, please remove the old hose assemblies owned by users and install them with new hose assemblies. Do not reuse the old hose assemblies to avoid related safety problems.
• The grounding wire of this product must conform to the stipulated construction mode, and the three-level grounding structure must be grounded, otherwise the use of this product is prohibited.
• Electric plug need to plug in the electric with air switch.
• In the same room where this product is installed, a switch of water inlet angle valve needs to be installed at a location within reach. It is used in emergency situations to cut off the waterway of this product without the aid of tools; otherwise, unexpected failures of this product may occur and it will cause user loss.
• If you have not used this product for a long time, please close the angle valve, press the water release button to drain the water of ceramic itself and cut off the power; When using the product again,please wash first to prevent water quality problems and skin diseases.
• When the outside air temperature is lower than 0°C, in order to prevent water leakage caused by external filter and other accessories likely freezing, please be sure to close the water inlet valve and drain the left water; If pipe has been frozen, please raise the room temperature and wait for pipe normal then use the toilet, otherwise the product may not be used normally.

Component list

SMART TOILET

Specifications

1. Rated power: Set the seat temperature to the highest level under the conditions of an ambient temperature of 68°F±41°F, inlet water static pressure 0.18MPa±0.02MPa, Turn on the flush function, and test the average power within 60 seconds.
2. Maximum power: Set the seat temperature to the highest level under the conditions of an ambient temperature of 73°F±35°F, an inlet static pressure of 0.18MPa±0.02MPa, Turn on the flush function and continue to work stably at the maximum power for a cleaning cycle.
3. Water consumption test: Test the water consumption separately under the water pressure 0.16Mpa and 0.55Mpa three times. Get six values in total, then divide the sum by six and the average is the nominal water consumption.

Parts Names

Product Drawings

Power and Water Supply Connection

• If the power cord is not long enough, please use the extension line which is made by certificated manufacturers.
• Only for reference.

Installation

Installation Precaution

We reserve the right to change, update, modify, alter, redesign this manual/product or its policies without prior notice! We shall not be liable for any injuries or property damages in connection with this product during installation or use of the product!
The product must be installed by a fully insured and licensed plumber only. Installation of the product by anyone other than fully insured and licensed plumber shall void limited warranty. We recommend that the licensed plumber have experience in the installation of the product. During unpacking the product and prior to installation inspect your new product for any damages or missing parts. Do not attempt to install or operate the product if the product is damaged.

Installation Tools

Product Installation

Install the water inlet valve

Clean the ground and dry the water before installation. Mark the central lines of the draining outlet, and install the inlet valve on the wall.

Mark the curve of ceramics

Align the drain hole of the ceramic with the central line. Mark the curve of ceramics for later installation. Silicone sealant application: Glue the outline with silicone sealant.

Toilet installation(Method 1)

1. Sealing ring installation
   Gently tilt the toilet sideways until it rests on the side surface. Install the sealing ring evenly along the outlet, and the small end of the sealing ring facing the toilet. Glue the edge of toilet bottom with silicone sealant, place the toilet base along the outline and position the toilet base.

2. Toilet (ceramic) installation
   Lift the toilet, take the floor drain as a reference, align the ceramic body of the toilet with the ceramic contour line drawn on the ground, and slowly put the ceramic on the ground so that the two marks overlap. After overlapping, press the ceramic down (can be pressed by the weight of the human body) so that the sealing ring fully contacts the ground.

   • Do not move the ceramic or shake it left and right after the marks are overlapped, otherwise the seal produced by the sealing ring may be damaged and cause water leakage.

Toilet installation(Method 2)

1. Remove the bidet seat
   Remove the fixing screws of the toilet; remove the connecting pipes and wires of the toilet, separate the bidet seat from the toilet.

2. Sealing ring installation

   • Place the sealing ring onto the flange.

3. Ceramic installation
   Glue the edge of the toilet bottom with silicone sealant. Line up the toilet base over the flage screws. Place the toilet base and secure the flange bolts. Glue the edge of the toilet bottom with silicone sealant, place the toilet base along the outline and position the toilet base.

4. Bidet seat installation
   Adjust the bidet seat to match the toilet, use screws to fix the bidet seat on the toilet.

5. Connect the water inlet valve and filter
   As shown in the following figures.
   NOTE:
   Do not use the smart toilet immediately after installation, use it after 48 hours.

6. Connect to the power
   Only connect this product to a properly grounded outlet.

7. Using the product for the first time

   • Connect to the power and open the water inlet valve. Check every function button of the remote control (only flush function) and side control. such as LED, seat temp adjustment, etc.

Instructions for Remote Control Installation

1. Use a coin or other objects to turn the base counterclockwise about 10° to unlock the base and and then use fingernail or sharp objects to remove the base.
2. Pull out the insulation sheet of the battery to make the remote connect to the power.
3. Code Pairing: After the remote and toilet are powered on and self-tested, press and hold the code pairing button for about 5 seconds. After a long “beep” prompt tone heard, the code pairing is completed.
4. Re-install the base and then use a coin or other objects to turn the base about
5. 10°clockwise to lock the base.
6. Clean the dust, oil stains, water droplets, etc. on the wall and wipe them clean.
7. Tear off the white sticker on the double-side adhesive tape on the back.
8. Choose a location close to the toilet (1 meter to 1.5 meters above the ground, adjust the height according to actual usage). Press the remote firmly against the wall evenly and let it sit for 24 hours.

Battery Replacement Instructions

1. Use a coin or other objects to turn the base counterclockwise about 10°to unlock the base and then use fingernail or sharp objects to remove the base.
2. Take out the CR2032 button battery.
3. Insert the new battery.
4. Re-install the base and then use a coin or other objects to turn the base about 10°clockwise to lock the base.

Remote Control Panel Using Instructions

Flush

• Press the button to flush the toilet.

Other Functions Instruction

Kick sensing

• Gently touch the foot sensor to activate the auto flushing function.

Pre-wetting

• Once sitting on the seat, the pre-wetting function will be activated to help reduce waste build-up.

Maintenance and Cleaning

Maintenance and cleaning of toilet lid and seat

1. Turn off the power, close the water outlet valve.
2. Use soft cloth to clean the lid and seat.
   • Be careful not to allow water to get inside or leave detergent in the gap between the top unit and the bowl unit.
   • Avoid using materials that will damage the surface. Clean the surface with a soft and wet cloth.
   • Corrosive chemicals or cosmetics (such as cleaners containing abrasive compounds and aftershave) can not be used to clean the lid and seat.
3. Turn on the power, open the the water outlet valve.

Maintenance and cleaning of the toilet bowl

1. Turn off the power.
2. Use a toilet brush and toilet detergent to clean the bowl.
   • Corrosive chemicals (such as cleaners containing abrasive compounds and strongly acidic cleaners or strong alkaline cleaners) should not be used to clean the bowl.
   • Wire brush or abrasive nylon scrubbing brush should not be used to clean the bowl.
3. Turn on the power.

Cleaning The Water Filter

1. Turn off the power Close the water outlet valve
2. Remove the water-inflow filter from the inlet hose.
3. Take out the filter by using a flat-blade screwdriver to unscrew the filter.
4. Remove the filter and rinse it with clean water.
5. Install the filter screen as it is, be sure to tighten it, otherwise, it will cause water leakage.

How to do

1. 1. When the toilet can not flush automatically due to a power outage.
   • Connect the smart toilet to the power bank through the TPYE-C interface.
2. When the toilet can not flush automatically due to a water outage.
3. Flush the sewage in the toilet away with a basin.
4. After flushing, add water to the toilet to avoid stinking.
5. When the product is left unused for long time
6. Turn off the power, and close the Angle valve, drain the water in the inlet hose.
7. Especially in winter, the water inside the hose of the toilet should be discharged to avoid freezing.

Trouble Shooting

Notice

When encountering a problem, please read the above common troubleshooting carefully, and follow the solution instructions for product maintenance; Please contact professional maintenance personnel, dealers or LEIVI after-sale service team in time to seek help. There may be differences between the contents of this manual and the actual product, and the actual product shall prevail.

Maintenance Service Sheet

Free maintenance regulation:

1. LEIVI warrants its products to be free from defects in materials and workmanship during normal use when properly installed and serviced, for a period of three (3) years from date of purchase. This limited warranty is extended only to the ORIGINAL PURCHASER of the product and is not transferable to any third party, including but not limited to any subsequent purchaser or owner of the product. This warranty applies only to LEIVI product is purchased and installed in USA and Canada.
2. LEIVI’s obligations under this warranty are limited to repair, replacement or other appropriate adjustment, at LEIVI’s option,of the product or parts found to be defective in normal use, provided that such product was properly installed, used and serviced in accordance with instructions. LEIVI reserves the right to make such inspections as may be necessary in order to determine the cause of the defect.
3. This warranty does not apply to the following items:
   • a) Damage or loss sustained in a natural calamity such as fire, earthquake, flood, thunder, electrical storm, etc.
   • b) Damage or loss resulting from any accident, unreasonable use, misuse, abuse, negligence, improper care, or maintenance of the product.
   • c) Damage or loss resulting from sediments or foreign matter contained in a water system.
   • d) Damage or loss resulting from the quality of water in the region where the product is used.
   • e) Damage or loss resulting from improper installation or from installation of the product in a harsh and/or hazardous environment, or improper removal, repair or modification of the product.
   • f) Damage or loss resulting from electrical surges or lightning strikes or other acts which are not the fault of LEIVI or which the product is not specified to tolerate, including failure to use the factory equipped cord and plug or use of a loose or faulty  electrical outlet or use of a current or socket other than a 120V, 60Hz electrical current from a GFI (ground, fused) socket.
   • g) Damage or loss resulting from normal and customary wear and tear, such as gloss reduction, scratching or fading over time due to use, cleaning practices or water or atmospheric conditions, including but not limited to, the use of bleach, alkali, acid cleaners, dry (powder) cleaners or any other abrasive cleaners or the use of metal or nylon scrubbers.

Executive standard: CONFORMS TO UL STD. 1431/UL STD. 1591 ASME A112.4.2-2021 Warranty period: within three years from the purchase date

• Due to the constant improvement of our products, we will keep the final interpretation of products change.
• If the products you bought exist differently from the instructions, please in kind prevail.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Add: Room 902, No. 370, Chengyi Street, Phase Ill Software Park, Torch High- tech District, Xia men City, Fujian Province, China.

• Email: support@ileivi.com
• Website: www.ileivi.com

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction

FAQ

• Q: Can I use any cleaning agents to clean the plastic parts of the toilet seat cover?
  • A: No, it is not allowed to use banana oil, gasoline, putty powder, nylon brush, or other non-neutral detergents to clean the plastic parts. This may cause chemical reactions, leakage, damage to the product, and potential injury.
• Q: Can I repair the product myself if it breaks down?
  • A: No, it is not recommended to disassemble or repair the product yourself. If necessary, seek professional repair person service to avoid causing further damage.
• Q: Can I use an extension cord if the power cord is not long enough?
  • A: No, it is not recommended to use an extension cord. Please ensure that the power cord is long enough to reach the power outlet.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>