Barrette OUTDOOR LIVING Juliette Brackets For Aluminum Rail Instruction Manual

June 5, 2024
Barrette OUTDOOR LIVING

Barrette OUTDOOR LIVING Juliette Brackets For Aluminum Rail

Barrette-OUTDOOR-LIVING-Juliette-Brackets-For-Aluminum-Rail-
PRODUCT

WARNING:

  • Improper installation of this product can result in personal injury. Always wear safety goggles when cutting, drilling and assembling the product.
  • Incorrect installation may cause harm to the product or individual.
  • Refer to local building codes for installation requirements; failure to install this product in accordance with building codes may affect the safety of the product and void product warranty.

NOTICE:

  • DO NOT attempt to assemble the kit if parts are missing or damaged.
  • DO NOT return the product to the store, for assistance or replacement parts call: 1-877-265-2220.

Component List

QTY Description
4 Juliette Bracket
2 Foot Support
2 Flat Post Cap
16 #14 x 1″ Hex head screw

TOOLS NEEDED

| Pencil
---|---
| Screwdriver
| Measuring Tape
| Power Drill
| Drill Bits

Barrette-OUTDOOR-LIVING-Juliette-Brackets-For-Aluminum-Rail-
FIG-1

  1. For use with Barrette Outdoor Living 2½” aluminum railing fascia posts:
    • a. Assemble your level railing section per the panels included instructions.
    • b. Mount brackets included with the railing panel to the posts by using included template as a guide.

The suggested position is:
Measure up 6″ from the bottom of the post. Mark with a line. From that line, measure up 3713⁄16″ for a 42″ panel (3113⁄16″ for a 36″ panel) and draw a line. Align the bottom of the bottom bracket with the first line, pre-drill the holes and secure the bracket with hardware included with the panel. Align the bottom of the top bracket with the second line, pre-drill the holes, and secure the brackets with hardware included with the panel.

Installation

Two (2) Juliette brackets will be used on each post.

  • a. Use the included mounting hardware – 1″ #14 hex head screw to attach one bracket approximately 2″ below the top rail bracket and one approximately 2″ below the bottom rail brackets
  • b. Repeat this for the second post.Barrette-OUTDOOR-LIVING-Juliette-Brackets-For-Aluminum-Rail-FIG-2
  • Attach pyramid cap to top of post and flat cap to bottom of post.
  • Position section in its mounting location and use 3⁄8″ diameter fasteners (not included) to attach the posts to the structure per the mounting schedule below:

POST MOUNTING HARDWARE REQUIRED (NOT INCLUDED)

FOR RESIDENTIAL APPLICATIONS, 36″ HIGH|
---|---



Panel Width

| ****



Load

| ****


Recommended Bolt Application

| For Lag Bolt Application 3/8″ Diameter Screw

Minimum Embedded Screw Thread Length Required

| ****


For Through Bolt Application

| For Concrete Anchor Application 3/8″ Titen HD Anchor Minimum Required Length (Minimum Distance of 4″ from Edge Required)|
8′| | Lag Bolt| 3.5″| 3/8 Hex Bolt 3/8″ Flat Washer 3/8″ Lock Washer

3/8″ Nut

| 4″|
| -or-|
6′| 3″| 3″|
200 lbs| Through Bolt|
| -or-|
4′| 2.5″| 3″|
| Concrete Anchor|
FOR COMMERCIAL APPLICATIONS, 42″ HIGH|
---|---



Panel Width

| ****



Load

| ****


Recommended Bolt Application

| For Lag Bolt Application 3/8″ Diameter Screw

Minimum Embedded Screw Thread Length Required

| ****


For Through Bolt Application

| For Concrete Anchor Application 3/8″ Titen HD Anchor Minimum Required Length (Minimum Distance of 4″ from Edge Required)|
| | Through Bolt| | ****


3/8 Hex Bolt 3/8″ Flat Washer 3/8″ Lock Washer

3/8″ Nut

| |
8′| 400 lbs| -or- Concrete Anchor| N/A| 5″|


6′

| ****

300 lbs

| Lag Bolt| ****

4.5″

| ****

4″

|
-or-|
Through Bolt|
| | | |
4′| 200 lbs| -or- Concrete Anchor| 3″| 3″|

  • a. Position the support foot so it fully engages the bottom rail.
  • b. Mark the 2 holes and attach the support foot with two ¼” diameter screws (not included)Barrette-OUTDOOR-LIVING-Juliette-Brackets-For-Aluminum-Rail-FIG-3

NOTE: One foot support is needed (centered) for a 6′ panel. Two foot supports equally spaced for an 8′ panel

If your span is greater than 8’ you will need a mid post. For this type of application a fascia mount mid bracket as well as a Juliette spacer (73050297) is neededBarrette-OUTDOOR-LIVING-Juliette-Brackets-For-Aluminum-Rail-
FIG-4

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Barrette OUTDOOR LIVING User Manuals

Related Manuals