Barrette OUTDOOR LIVING BOL-WEB Aluminum Racking Gate Kit Instruction Manual

: October 30, 2023
: Barrette OUTDOOR LIVING

Table of Contents

BOL-WEB Aluminum Racking Gate Kit
BEFORE YOU BEGIN:
Racking Gate Kit Components:
Installing Gate Uprights
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OUTDOOR LIVING BOL-WEB Aluminum Racking Gate Kit
Instruction Manual

BOL-WEB Aluminum Racking Gate Kit

Read all instructions prior to installing product.
Refer to manufacturers safety instructions when operating any tools.

To register your product, please visit: barretteoutdoorliving.com

WARNING:

Improper installation of this product can result in personal injury. Always wear safety goggles when cutting, drilling and assembling the product.
Incorrect installation may cause harm to the product or individual.

NOTICE:

DO NOT attempt to assemble the kit if parts are missing or damaged.
DO NOT return the product to the store. For assistance or replacement parts call: 1-800-265-2220.

BEFORE YOU BEGIN:

Check your local zoning laws.

Local zoning laws and Home Owners Associations may regulate the location, style and height of your fence and gate or even require a permit signoff beforehand.
Check local codes for frost line depth and regulations.
Additional products and assembly may be required to meet wind code requirements. Notice of acceptance (NOA) can be found at www.miamidade.gov/building/pc-search_app.asp
Contact your local utilities companies.
You must have the utility companies clearly mark your property for electrical, gas or water lines to avoid puncturing any unseen underground utilities.

TOOLS NEEDED:

Safety Glasses
Level
Tape Measure
Drill
Drill Bits
Pencil
2″ Spacer Blocks (2)
Saw
Clamps

Racking Gate Kit Components:

QTY.		Description
2	A	Gate Uprights
2	B	2″ Pyramid Post Tops
1	C	Gate Stop
1	D	Latch
2	E	Butterfly Hinges
1	F

F1
F2
F3
F4
F5
F6| Hardware Bag:
• (2) Rail Grippers
• (4) M6 Acorn Nuts
• (4) M6x45mm Bolt
• (6) #10×1″ Screws
• (4) M6 Washers
• (2) U-Channel Blocks

To obtain and review a copy of the warranty please visit barretteoutdoorliving.com.
You may also contact us at 1-877-265-2220 or email CS.outdoorliving@barretteoutdoorliving.com.

a. Preparing and cutting panel down for straight applications:
a. Measure your gate opening and subtract 1 5⁄8″ from that length.
b. Take that length and lay your tape measure on the panel. Center your tape measure to where the pickets are even on both sides (Fig. 1). Draw
a line on both sides of each rail.
c. Cut along drawn lines. 1.b. Preparing and cutting panel down for racked applications:
a. Lay panel on a clean working surface and rack to desired angle (Fig. 2). (Max of 10 degrees or 12 3⁄4″ high). b. Lay gate uprights (A) on a fence panel parallel to pickets (Fig. 3). c. Measure gate opening; subtract 1 5⁄8″.
d. Space gate uprights to measured length; adjust to where pickets are spaced evenly. e. Mark each rail where the upright lies (Fig. 4).

Installing Gate Uprights

a. Install the now cut panel in one of the gate uprights.
b. Rack the panel at the desired angle and push the panel to the back of the upright (A) to where there is no gaps (Fig. 5). c. Using two clamps, clamp the gate and upright together from the back of the first picket to the back of the upright (Fig. 6). This will help in preventing the panel from moving in the following steps.
Take the two Rail Grippers (F1) in your Hardware Bag and install them on both sides of the rail inside of the upright brackets (Fig 7).
Using a 1⁄4″ drill bit, drill a hole all the way through rail using the two pre-drilled holes on the rail grippers. If your gate width has a picket between the slots (Fig. 8) drill thought the picket as well.
Using 2x M6 Bolts (F3), 2x M6 Acorn Nuts (F2), install hardware as shown (Fig. 9).
If there is no picket inside of the bracket area, place one U-Channel Block (F6) around the first bolt. This will prevent the bracket from deforming when tightening the bolts down (Fig. 10).
Tighten bolts down.
Using 3x #10×1″ Screws, install one (F4) per rail 5⁄8 ” from the back of the gate upright and aligned with the rail (Figs. 11&12).
Remove clamps from gate.
Repeat steps 2-9 to install the second gate upright.