KINGANT S04 Electric Adjustable Height Standing Desk Instruction Manual

S04 Electric Standing Desk
Operation Manual

S04 Electric Adjustable Height Standing Desk

If you have any questions during the installation process, or have better suggestions for our products, please feel free tocontact us at KINGANT- Service@Kagn-tech.com.

Caution

Keep children and pets away from the electric height-adjustable desk during the operation. Unplug the power cord during a thunderstorm or if you do not intend to use the desk for a long time.
Make sure desktop not touching the wall.
Ensure no obstacles in the desk’s path and no object above and 20” under the desk.
Working environment temperature 0-40℃, keep products away from corrosive gas, liquid and dusty objects.
It is strictly forbidden to disassemble the products privately to avoid that the failure of the products or the damage to the human body caused by electronic products, etc.
Although the product with anti-collision function, in order to avoid any pinching, please ensures that hands or other parts of your body are in a safe position during the operation. Anti-collision is not enabled during all resets.
Please read the following instructions carefully before start using the highadjustable desk. The company does not bear any warranty or liability for damage and human injury caused by any abnormal operation.
It is necessary to reset manually after the initial installation or power off.

Parts List

Assembly

Instruction

Before resetting, please note:

1. Make sure the desk is on flat ground.
2. No obstacles under the desk.
3. No heavy things at the desk.

Manual Reset
It is necessary to be reset manually after the  initial installation and power off.

1. Keep pressing down key till the desktop till display shows“E-1”and“rES” alternately and release the key.
2. Keep pressing down key, the desktop will move slowly down and retum  back till the display shows“27.5/070”.
3. Release the key, the height-adjustable desk resetting finished.
   Note: The anti-Collision function is not enabled during all resets. Please note that there is a potential risk of pinching in this case, and be sure no obstacles in the desk’s path.

Up and Down

1. Keep pressing“up”key till the required height is reached.
2. Keep pressing“down”key till the required height is reached.

Saving position

1. Adjust the desktop to the height you want to save.
2. Press“M”key，till the display will show“S–”.
3. Press“1”，and the display will show alternately as“S-1”and the desktop height.
4. Press“M”key，the first memory position is set successfully. Similar progress for 2 and 3 memory positions.

Anti-Collision function
Before use, please make sure removing obstacle in advance and human body is in the safe position.

1. Once the desktop encounters any obstacle in its path, the screen displays“E-2”。
   The desktop will move a defined distance in opposite direction, and it would be used normally after removing the obstacle.

Container and self-stop positions
Do not enable this function only when you are really need in some situation.

1. Keep pressing the key“M”for 3 seconds till the display shows“S–”to enter setup menu.
2. Press up key till the display flash as“HLP”.
3. Press“1”，the display show alternately as“H-P”and current height.
4. Keep pressing up or down key till the required upper limit position is  reached.
5. Press“M”,the desktop height will be showed and the shelf stop position has been set.
6. Press “2”, the display will show altemately “L-P” and current height, keep pressing down key till the lower limit position is reached, press “M”, the container stop position has been set.

Note: By this function would be used to limit the movement area of desktop, when the container is underneath or any shelf above the desktop. Once it is set, the new upper or lower limitation will be stored.

Change the displayed Unit（cm/inch)

1. Keep pressing key“M”till the display show“S–”to enter the setup menu.
2. Press “UP”key,the display will show“Unt”.
3. Press“1”，and the display will show alternately as“Unt”and the desktop height unit by“cm”.
4. Press“M”key to save the unit as cm.
5. Press“2”，and the display will show alternately as“Unt”and the desktop height unit by“inch”,press key“M”to save the unit as inch.

Amend the desktop height displayed

1. Keep pressing key“M”till the display show“A – -”.
   Press“Up”or“Dn”several times,till the display show“End”and height.
   (In this case, the unit is mm or inch when this system’s metric or imperial)

2. Press“1”,“2”and“3”respectively, and to adjust the first number, the second number and the third number.If you click one,the number will increase by 1, till you get to the value you want.

3. Press“M”the height has been changed to defined digit.

Note: The function enables you to change the height shows on the display based on the actual measurement.

Plug detection
The function can detect whether the motors are collected normally

1. Once the display shows“E-3”and“rES”，it reminds you check whether any motors fail connected with control unit. Please connect the main cable again,wait at least 5 seconds.
2. Connect all the plugs.
3. Follow “Manual Reset ”procedure.

Restore factory setting
With this functin,you can make the control unit to factory setting.

1. Keep pressing “M” till the display shows “FAC”.
2. Press “M”,and the control unit to factory setting (including memory position, container-and shelf-stop position,etc).

Code meaning and Trouble shooting

【Code meaning】

further operation
E-2| Anti-Collision function| It can be used normally after removing the obstacle
dut| Operated continuously
without suitable rest| Make the desk rest around 18minutes for further operation

【Trouble shooting】

to manual reset
E-3| Check the cables and ensure they are well connected, and the  height- adjustable desk can be used normally after manual reset

Technical Data

Caution
Please read this manual carefully. If this desk changes hands, please provide this manual to the new owner.
Make sure the desktop is not touching any obstacles or walls and that no obstacles are in the path of the desk. Make sure all cords are of an appropriate length to accommodate the full range of height adjustments.Keep children away from desk components.  There  is a risk of injury and electric shock. Do not sit or stand on the desk frame. Do not crawl or lie under the desk frame.
Do not open or modify any of the components including the lifting columns, control box, or handset. Doing so risks electric shock and voids the warranty.
Placing objects taller than 20″ underneath the desk will obstruct the desk’s movement and may result in physical damage.

Voltage Converters
Using a voltage converter could cause damage to the desk and is improper use.The resulting damage is not covered by the Converters warranty.
Verify the voltage of the control box as labeled to avoid damage.
Replacement voltage control boxes are available from Kingant.
This desk has an electric motor and is designed for use in drywork environments only.

Use & Liability
This Kingant desk is adjustable so it can be positioned at an optimal ergonomic height.
Any extraneous use is at the user’s own risk. Under no circumstances does the manufacturer accept warranty claims or liability claims for damage caused by improper use or handling of the desk frame.

Safety Warning
Please read this manual carefully before use.

1. For indoor use only.
2. The product must be connected to the correct power supply.
3. For any accessories connected to the control box, the plugtype and electrical characteristics must conform to its specifications.
4. If the transformer’s external cable is damaged and needs to bereplaced, a replacement part will be provided by the manufacturer or its service agent.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>