Barrette OUTDOOR LIVING 73050573 Louvered Fence Panel Louvered Fence Posts Instruction Manual

: October 30, 2023
: Barrette OUTDOOR LIVING

Table of Contents

73050573 Louvered Fence Panel Louvered Fence Posts
BEFORE YOU BEGIN:
TOOLS/MATERIALS NEEDED:
Component list:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LOUVERED FENCE
Installation Instructions

73050573 Louvered Fence Panel Louvered Fence Posts

Read all instructions prior to installing product.
Refer to manufacturers safety instructions when operating any tools.
To register your product, please visit: barretteoutdoorliving.com
WARNING:

Improper installation of this product can result in personal injury. Always wear safety goggles when cutting, drilling and assembling the product.
Incorrect installation may cause harm to the product or individual.
Check local building codes to determine pool-safe fencing options.
NOTICE:
DO NOT attempt to assemble the kit if parts are missing or damaged.
DO NOT return the product to the store. For assistance or replacement parts call: 1-877-265-2220

BEFORE YOU BEGIN:

Check your local zoning laws.

Local zoning laws and Home Owners Associations may regulate the location, style and height of your fence or even require a permit signoff beforehand.
Check local codes for frost line depth and regulations.
Additional products and assembly may be required to meet wind code requirements.

Notice of acceptance (NOA) can be found at
www.miamidade.gov/building/pc- search_app.asp
Contact your local utilities companies.

You must have the utility companies clearly mark your property for electrical, gas or water lines to avoid puncturing any unseen underground utilities.

TOOLS/MATERIALS NEEDED:

| Louvered Fence Posts
---|---
| Post Tops
| Concrete
| Coarse Gravel (6″ per hole)
| Post Hole Digger/Shovel
| String Line Stakes with String
| Level
| Tape Measure
| Safety Glasses
| Glue

Component list:

QTY.	Description
13	Boards

To obtain and review a copy of the warranty please visit barretteoutdoorliving.com.
You may also contact us at 1-877-265-2220 or email CS.outdoorliving@barretteoutdoorliving.com.

Mark the fence location using string and line stakes (Fig. 1).
NOTE: Plan gate placement, opening and hardware clearance before installing fencing.
.Post Location:
Measure the width of the fence panel (X) plus the width of the post (Y). This is the common centerto-center measurement (unless there is a cut-down panel) for post hole location (Fig.2).
Post Installation:
Dig first two post holes in diameter based on size chart below* and down to your specified frost line. Insert filler/gravel into the bottom of both holes and
then set first post in post hole.
Add wet or dry concrete mix according to the manufacturer’s instruction to the top of the hole for first post only and level it.
Example: When your frost line is 36″ insert 12″ of gravel/ filler and 24″ of post with concrete surrounding (Fig. 3).

Diameters based on post size:

10″ for 5″ x 5″ post
8″ for 4″ x 4″ post
3. Insert 6″ of gravel/filler into the bottom of both holes and then set both posts into the ground and level the first post.
Add wet or dry concrete mix according to manufacturer’s instructions to the top of the first post hole (Fig. 4). Make sure panel will be 2″ above the ground.
After setting first fence section, proceed systematically with post, panel, post, etc.

Insert board into the bottom post route. Then insert the board into the bottom post route on the other post (Fig. 5).
Ensure that the lock tab is securely inserted into the post (Fig. 6).
Continue working your way upwards inserting boards until all 13 boards are installed (Fig. 7).
Apply glue on inside rim of post tops then attach to posts (Fig. 8). Repeat these steps until completed.

Barrette Outdoor Living
7830 Freeway Circle, Middleburg Heights, OH 44130
barretteoutdoorliving.com • (877) 265-2220