Barrette OUTDOOR LIVING 34111504 Gate Framing Kit

Product Information

The Gate Framing Kit is designed for use with Linden and Acadia Panels. It includes all the necessary components to install a gate, including gate uprights, upright caps, screws, vinyl cement, hinges, latch, gate stop, U-channel, top rail boards, and bottom rail. It is important to note that vinyl gate posts require an internal support system for weight-bearing purposes, so a post stiffener needs to be purchased separately. The user manual provides detailed instructions on how to install the product safely and securely.

For warranty information or to register your product, please visit barretteoutdoorliving.com or contact the customer service team at 1-877-279-4496 or Cs.outdoorliving@barretteoutdoorliving.com

Product Usage Instructions

1. Apply vinyl cement to all inside surfaces of the first upright where the rails will be inserted.
2. Insert both rails into one upright assembly.
3. 1. Place the U-channels on the end boards, then slide the boards into rails, locking them together.
4. Apply vinyl cement to all inside surfaces of the second upright where rails will be inserted.
5. Attach the remaining upright assembly to the rails making sure the boards fit snugly.
6. Measure diagonally from top of the left corner rail (A) to the bottom of the right corner rail (B) and note the length. Then, measure diagonally from the top of the right corner rail (C) to the bottom of the left corner rail (D). Note the length. Make sure both measurements are the same before installing screws into the uprights.
7. Install two 6 screws (provided) through each upright insert and into the rail using the molded grooves on the insert as a guide.
8. Install upright caps onto the top of each upright with provided vinyl cement.

Note: Before starting the installation process, read all instructions carefully and refer to the manufacturer’s safety instructions when operating any tools. Use the tools and materials listed in the user manual, including a Phillips screwdriver, safety glasses, line level, tape measure, drill, #2 square drive bit, 2 wood blocks, and 3/32 bit square pencil.

• Read all instructions prior to installing the product.
• Refer to manufacturers’ safety instructions when operating any tools.

To register your product, please visit: barretteoutdoorliving.com

WARNING:

• Improper installation of this product can result in personal injury. Always wear safety goggles when cutting, drilling, and assembling the product.
• Incorrect installation may cause harm to the product or individual.
• Not pool code approved.

NOTICE:

• DO NOT attempt to assemble the kit if parts are missing or damaged.
• DO NOT return the product to the store, for assistance or replacement parts call: (877) 265-2220.

BEFORE YOU BEGIN

Vinyl gate posts require an internal support system for weight-bearing purposes therefore a post stiffener is required. Post stiffener needs to be purchased separately.

TOOLS/MATERIALS NEEDED

• Linden Panel
• Phillips Screwdriver
• Safety Glasses
• Line Level
• Tape Measure
• Drill

• 2 Square Drive Bit

• 2″ Wood Blocks
• 3⁄32″ Bit
• Square
• Pencil

Linden Gate Component list:

Description

• Gate Uprights
• Upright Caps
• Screws
• Vinyl Cement
• Hinges
• Latch
• Gate Stop

To obtain and review a copy of the warranty please visit: barretteoutdoorliving.com. You may also contact us at 1-877-279-4496 or email Cs.outdoorliving@barretteoutdoorliving.com

INSTALLATION INSTRUCTION

1. Apply vinyl cement to all inside surfaces of the first upright where the rails will be inserted (Fig. 1).
2. Insert both rails into one upright assembly (Fig. 2).
3. Place the U-channels on the end boards, then slide the boards into rails, locking them together (Fig. 3).
4. Apply vinyl cement to all inside surfaces of the second upright where rails will be inserted.
5. Attach the remaining upright assembly to the rails making sure the boards fit snugly.
6. Measure diagonally from the top of the left corner rail (A) to the bottom of the right corner rail (B) and note the length. Then, measure diagonally from top of right corner rail (C) to the bottom of left corner rail (D). Note the length. Make sure both measurements are the same before installing screws into the uprights (Fig. 4).
7. Install two 6″ screws (provided) through each upright insert and into the rail using the molded grooves on the insert as a guide (Fig. 5).
8. Install upright caps onto the top of each upright with provided vinyl cement (Fig. 6).
9. Check the included Barrette Outdoor Living® hinge, latch, and gate stop kit for hardware instructions, or visit barretteoutdoorliving.com to obtain a copy.

Barrette Outdoor Living 7830 Freeway Circle, Middleburg Heights, OH. 44130 barretteoutdoorliving.com • (877) 265-2220

References

• Barrette Outdoor Living: HomePage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>