JONATHAN Y JYL9909 Harper 1-Light LED Sconce Instruction Manual
- October 30, 2023
- JONATHAN Y
Table of Contents
JONATHAN Y JYL9909 Harper 1-Light LED Sconce
Product Information
The JYL9909 is a lighting fixture that requires installation by a licensed electrician. It comes with a mounting bracket, back plate, glass shade, and machine screws. The product dimensions are 4.5”W x 10H x 5E. The lamp requires a Type A bulb with a maximum wattage of 40 or a CFL/LED bulb with a maximum wattage of 13/9.
Product Usage Instructions
- Before beginning assembly, ensure that all parts are present and undamaged.
- Switch off the main electrical supply from the main fuse box/circuit breaker before installation.
- Fix the mounting bracket to the outlet box with machine screws.
- Make wire connections with wire connectors according to the reference chart provided in the manual.
- Wrap the ground wire from the outlet box around the green ground screw on the mounting bracket. Tighten the ground screw.
- If the fixture is supplied with a ground wire, connect it to the outlet ground wire with a wire connector.
- Orient the back plate so that the holes in the ears on the side of the mounting bracket are aligned with the holes in the rear plate, and then secure with machine screws.
- Install a bulb with wattage no greater than specified on this fixture. Always ensure that electrical current is turned off before changing bulbs.
- Place the glass shade on the back plate, align the holes above, and then rotate the nut to fix them.
- If you need to replace or install a new bulb, please loosen the nut, take out the glass shade from the back plate and install the bulb.
- Enjoy your lamp!
Model#: JYL9909
Product Dimensions: 4.5”W X 10″H X 5″E
WARNING
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED
ELECTRICIAN.
WARNING
SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER
BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF
THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE
RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE
To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean clorth (use clean water, never a solvent) to wipe the interior surface of the fixture. Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE & IMPORTANT SAFETY INSTRUCTIONS
- Please make sure that you have all parts indicated before you begin assembly of this item
- This item should be assembled on a soft surface to prevent scratching the finish during assembly
- To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation
- The external flexible cable or cord of this lamp cannot be replaced If the cord is damaged, the lamp shall be destroyed
Part List and Hardware List
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package contents list and hardware contents list. If any part is
missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 20 minutes.
- Fix the Mounting Bracket(B) to the outlet box with machine Screw(A).
- Make wire connections, with Wire Connectors(C), following the reference chart listed below.
Connect, Hot, Black or Red Outlet Supply Wire to:| Connect, Neutral, White
Outlet Supply Wire to:
---|---
Black| White
Parallel Cord (round & smooth)| * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored stripes)| Clear, Brown,
Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor| Insulated Wire (not
green) with Silver metal conductor.
Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions
- For installation in the United States: Wrap ground wire from outlet box around green ground screw on mounting bracket, no less than 2″ from wire end. Tighten ground screw.
- If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector.
- For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting bracket. Tighten ground screw.
- Orient the Back Plate (D) so that the holes in the ears on the side of the mounting bracket are aligned with the holes in the rear plate, and then secure with Machine Screws (E).
- Install Bulb(F). Be sure to use light Bulb(F) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs.
- Place the Glass Shade (G) on the Back Plate (D), align the holes above, and then rotate the Nut (H) to fix them
- Please loosen Nut(H) , take the Glass Shade(G) out from the back Plate(D) before install bulb.
PLEASUE USE TYPE”A” BULB MAX 40-WATT OR CFL BULB MAX 13-WATT OR LED MAX 9-WATT THERE ARE 1 X 4W LED BULBS IN THE BOX.
ENJOY YOUR LAMP
Documents / Resources
|
JONATHAN Y JYL9909 Harper 1-Light LED
Sconce
[pdf] Instruction Manual
JYL9909 Harper 1-Light LED Sconce, JYL9909, Harper 1-Light LED Sconce, 1-Light
LED Sconce, LED Sconce, Sconce
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>