GE 22003 Pre-Lit Christmas Trees Instruction Manual

: October 30, 2023
: GE

Table of Contents

Assembly Instructions
Troubleshooting Tips
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

22003 Pre-Lit Christmas Trees
Instruction Manual

Assembly Instructions

Nicolas Holiday Ltd. thanks you for purchasing this pre-lit Christmas tree. Should you have any problems with your tree, visit us at www.geholidaylighting.com for more information. You can call our toll free number at 1-877-398-7337.
Check our website for latest service hours and assembly instruction videos.
TREE ASSEMBLY DIAGRAM

SCHEMATIC DIAGRAM

NOTE: No tools required

| Tree Sections| Tree Stand| Approx. Asm Time*
---|---|---|---
7.5 ft tree| 3| Metal| 10 – 15 minutes

Carefully unpack the carton. Remove bubble wrap and inspect the sections of your tree. The carton should include sections”A”, “B” and “Top”, as well as a Tree Stand.
The tree stand should be open and set at 90° angle.
Insert Section A into tree stand, tighten the thumbscrew. Then insert the plug into an electrical wall outlet.
Untie RED twist-tie to release branch panels. All branches should fall into place with a gentle pull on the outer layer of branches.
Fig. A. Start at the inner and stagger the tips. Move each tip up to 40°. Fig. B. Make tips 2 & 3 to horizontal, tip 4 to vertical and tips 5 and 6 up to 45°.
To assemble the section “B”, properly insert section “B” into the top of section “A”. (See Fig. C)
Adjust branch tips, as needed, for a fuller look. To electrically connect the sections, fully insert the plug from the extension cord attached to the pole of the middle section into the extension cord outlet attached to the pole near the top of the bottom section.
Repeat “Step 4” for shaping.
To assemble the tree top, properly insert the “TOP” section into the top of section “B”. (See Fig. D) Adjust branch tips, as needed, for a fuller look. To illuminate the top, fully insert the plug from the top section into either the end connector or the extension cord outlet on or near the top layer of branches of previously assembled pole.

Troubleshooting Tips

If the tree does not illuminate, make certain the wall switch is turned on.
If one section of your tree does not illuminate, check that section for loose or missing bulbs, all factory connections are properly made or that you properly made all the electrical connections between each tree section,
Also, check the fused plug for a missing or burned out (open) fuse.
DISCLAIMER : DO NOT USE OR INSTALL ANY ADDITIONAL CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS POWERED BY A LIGHT BULB SOCKET. DOING THIS MAY RESULT IN DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE PERSONAL INJURY. DOING THIS, WILL RESULT IN A VOID OF THE LIMITED WARRANTY OF THIS PRODUCT.
Disconnect the decorative item from the power source before performing any maintenance or cleaning.
For indoor use only 120V
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY. GE is a trademark of General Electric Company and is under license by Nicolas Holiday Ltd.
©2022 Nicolas Holiday Ltd.
9 F., No. 37, Guanghua North Rd., Taipei, Taiwan 10560 All rights reserved.
Printed in China 22003LO
Tree Storage

Remove the tree’s main extension cord plug from the wall outlet.
Starting at the top, disconnect the “TOP” from section “B” and then disconnect section “B” from section “A”. {Fig. 1}
Note: Gently fold the tips in branches and fold the branches up toward the center. {Fig. 2}
Care should be taken to avoid damage to the lights.
Remove section “A” from the tree stand and close tree stand to place into the carton.
Refer to the drawing on how to repack your tree. {Fig. 3}

GE 22003 Pre-Lit Christmas Trees - FT TREEb IMPORTANT: Store your carton neatly in a cool, dry location protected from sunlight to prolong the tree life and to better keep the light sets in working order. Do not place a heavy load on the carton to avoid damage to or crushing the carton and tree inside.