Crane IQWrench3 Digital Torque Wrench User Manual

October 30, 2023
Crane

Crane IQWrench3 Digital Torque Wrench

Notice

ALL RIGHTS RESERVED. Reproduction of any part of this manual in any form whatsoever, without the prior permission in writing from Crane Electronics Ltd is forbidden.
Copyright © November 2022 by Crane Electronics Ltd.

ADDRESS

Manufacturer: Crane Electronics Ltd
Address: 3 Watling Drive Sketchley Meadows Hinckley Leicestershire LE10 3EY
Tel: +44 (0)1455 25 14 88
Technical Support : support@crane-electronics.com
Sales:sales@crane-electronics.com

UKCA MARKING

Crane Electronics Limited declares that the IQWrench3 has been assessed and complies with the UK regulatory requirements.

Crane Electronics Limited declares that the IQWrench3 has been assessed and complies with the UK regulatory requirements.

CE MARKING

Crane Electronics Limited declares that the IQWrench3 has been assessed and complies with the requirements of the relevant CE Directives.

COMPLIANCE

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installations. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

PRODUCT DISPOSAL

Applicable in the EU and other European Countries with separate collection systems
The symbol shown here and, on the product, means that the product is classed as Electrical or Electronics Equipment and should not be disposed with normal commercial waste at the end of its working life.

The Waste of Electrical and Electronics Equipment (WEEE) Directive (2012/19/EU) has been put in place to recycle products using best available recovery and recycling techniques to minimise the impact on the environment, treat any hazardous substances and avoid the increasing landfill.

To enable this product to be disposed of properly i.e., cradle to grave, Crane Electronics is willing to accept the return of your product (at your cost) for recycling or alternatively, for more detailed information about recycling of this product please contact your local authority or the Distributor / Company where you have purchased the product.

Battery disposal to take place in line with the AMENDED BATTERIES DIRECTIVE 2013/56/EU. Batteries must not go to landfill.
Check with local legislation.

Crane Electronics declares that this product does not contain any of the 191 Substances of Very High Concern (SVHC’s) identified in the REACH Regulation in used articles make-up.

In Countries outside the EU:
If you wish to discard this product, please contact your local authorities and ask for the correct way of disposal.

Signed for & on behalf of Crane Electronics Ltd.

Name: B. M. Etter
Title: Safety & Environmental Advisor

Signature of Issuer:

ABOUT THIS MANUAL

This manual covers the IQWrench3.
This wrench works with our TCI Lineside Controller, TorqueStar Data Collector (RF) and IQVu.
Actual screen shots or images represented in this manual may differ slightly from those on the actual product, depending on the version.

PACKING LIST

The following items are supplied with the IQWrench3 depending on model specification purchased.

1 x IQWrench3
1 x Quick Start Guide (with QR link to Operators Manual)
1 x Calibration Certificate
1 x Programming Cradle
1 x 1 Meter USB C Cable
1 x ID Head

Please ensure all items are present and notify Crane Electronics Ltd immediately of any shortages.

SPARES AND ACCESSORIES

Battery Pack
Charging
Cradle + Power Supply Unit
USB-C Cable
Comms Cradle

CARE AND STORAGE

Operating Temperature Range:
+5°C to +40°C
Storage Temperature Range:
-20°C to +50°C
Humidity:
10-75% non-condensing.
IP Rating:

IP50
The IQWrench3 may be wiped clean with a soft cloth.

FEATURES AND DIMENSIONS

OVERVIEW ­ IQWrench3

The IQWrench3 is a wireless audit and production wrench with built-in data collection features. There are two versions, an advanced Quality Auditing model or the robust Production model. Torque and Angle data can be viewed in real-time on the colour OLED screen.

The IQWrench3 reads the Torque and Angle values in real time and converts them to digital values. The wrench analyses the digital samples using measurement algorithms to calculate properties of the fastening. The IQWrench3 can communicate using RF with a 10m range*. Advanced software and torque measurement modes are available, including MoveOn, Yield and Re-tighten.

The IQWrench3 is powered by a replaceable Lithium-Ion battery pack.

  • The range of communication (Bluetooth, WiFi, RF) depends on the environment in which the IQWrench3 and TCI/PC are being used and the figure quoted is for a relatively metal free work space with the other device in line of sight of the IQWrench3.

SPECIFICATIONS

Physical Measurement:
Bi-directional torque and angle. Pulse count.

Measurement Modes:
Track: Real time display of applied Torque + Angle. Peak: Capture of highest Torque value during the cycle. Angle: Capture of highest Angle value during the cycle. Audit: Special measurement algorithm that measures torque after joint moves a certain angle. MoveOn: Special measurement algorithm that measures torque of previously tightened joint. MoveOn Adv.: Capture MoveOn point. If this value cannot be calculated, an Audit value is given instead. Yield: Special measurement algorithm for use with joints being taken into plastic region. Retighten: Special measurement algorithm that untightens a fastened joint and retightens to the same angle On the start up splash screen, the torque range (span), serial number and calibration due date of the wrench are displayed.

Reading Storage:
The IQWrench3 can store over 3000 jobs and 20,000 readings in storage mode with time and date stamp.

LEDs:
The IQWrench3 features:
Charge LED used when charging battery pack.
360° Status LED Light Ring for fastening status.
Shaft torch for illuminating target areas.

Zero Stability:
<± 0.02% FSD / °C

Static Accuracy:
±0.25% FSD

Angle Measurement:
Sample every 1ms

Battery Pack:
Re-chargeable Lithium-Ion battery.
Capacity 2000mAh 3.7V Weight 108.6g Useable battery life of 8 hours with normal usage

Communication:
Communicates via USB-C and the supplied cradle.
Warranty:
12 months parts and labour against faulty workmanship or materials.
Display:
40mm x 30mm colour OLED display

MAIN FUNCTIONS & FEATURES

BATTERY

The IQWrench3 unit has a battery pack that contains a Lithium-Ion battery. From fully discharged the unit will require a maximum of 4 hours charge to attain maximum capacity.

The full capacity of the battery is 2000mAh which yields approx. 8 hours of normal use.

When a IQWrench3 is placed in the charging cradle, the charge indicator LED will illuminate with colour according to the charge status.

Battery Charge Status will have 2 colours:

  • Red = Charging
  • Green = Charged
  • No LED = No charging source present and running off battery power.

Battery Charge Status will be available even when the IQWrench3 is OFF. It will only be viewable when connected to a charging source.

WARNINGS

Changes or modifications to the IQWrench3 not expressly approved by Crane Electronics Ltd could void the user’s authority to operate the equipment.

Observe maximum torque of the wrench before use.

Maintain unit with care. Keep unit clean for better and safer performance.

Changes or modifications to the IQWrench3 not expressly approved by Crane Electronics Ltd could void the user’s authority to operate the equipment.

Always operate IQWrench3 with approved battery pack.

Always operate, inspect and maintain this unit in accordance with all regulations (local, state, federal and country) that may apply.

Do not remove any labels.

Always use Personal Protective Equipment appropriate to the tool used and material worked.

Keep body stance balanced and firm. Do not overreach when operating with the tool. Anticipate and be alert for sudden

changes in motion, reaction torque, or forces during the operation.

Ensure work pieces are secure. Use clamps or vices to hold work pieces whenever possible.

Never use a damaged or malfunctioning tool or accessory with this unit.

Follow instructions for changing accessories.

Do not operate this product in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.

This unit contains no user serviceable parts. Only qualified service personnel should replace or fit parts.

BATTERY WARNINGS

Charge the IQWrench3 before use.

Only charge the IQWrench3 in the specified cradle.

Keep battery pack terminals clean.

Always store the battery pack in a dry place. Do not short circuit the battery pack.

Do not disassemble the battery pack.

Do not expose the battery pack to high temperature.

CHARGING THE IQWRENCH3

Wrench can be charged by inserting into the charging cradle.

IQWRENCH3 BUTTONS

IQWrench3 has a keypad with 6 buttons:

  • Press the red button to turn the wrench ON. When the splash screen appears showing the software version, calibration date and serial number, press the green button to continue to the menu.
  • When the wrench is on, the red button is also used to cancel/go back.
  • Use the green button to `select’.
  • To navigate the menus, use the arrow keys to move around.
  • To switch the wrench OFF, navigate to the power icon in the main menu and `select’ it, then press
    continue.

The IQWrench3 will switch OFF after a set period of inactivity. This time can be set in the power section of the settings.

LIGHT RING

During and after fastening the Light Ring will indicate the primary parameter status, which will be Torque except for Peak Angle Control, in which case it will be Angle.

  • Amber = LO
  • Green = OK
  • Red = HI

If the secondary parameter exceeds its specified limit the Light Ring will go Red regardless of the state of the primary parameter.

The Light Ring will start indicating the status as soon as the Torque goes above threshold.

When a new Job is received the Light Ring will cycle twice through sequence Amber, Green, Red to indicate a Job has been received and loaded. It will do the same on power up and the Job is already loaded.

When a Job is complete the Light Ring will continuously cycle through the sequence Amber, Green, Red whilst data is present.

ID HEADS/ADAPTER LENGTH COMPENSATION

The IQWrench3 is compatible with the Crane 1-Touch ID Head recognition system. The Crane 1-Touch system allows the wrench to compensate for special head designs that do not use the standard insert head dimensions.

The Crane 1-Touch Heads can be programmed with an ID from 1 through to 126, if there is no ID then the IQWrench3 will not use the ID system and treat the head as a standard insert head, with a critical compensation length of zero. They can also be programmed with a compensation length from 0 to 200 mm. When the wrench recognises that there is an ID Head present, it will automatically compensate the Torque by the critical length programmed into the head.

The 1-Touch ID Heads can be programmed up to 4 times, therefore if the compensation value needs to be updated, this can be done up to 3 times. This programming is done by Crane Electronics.

Below is a diagram of how to calculate the critical length for an ID Head.

CONTACT US

To get in touch with Crane Electronics, please go to https://crane- electronics.com/contact-us/
Crane Electronics Inc – if you are based in North America (Canada, USA, Mexico)

1260 11th Street West Milan Illinois 61264 USA
+1 309-787-1263
salesusa@crane-electronics.com
supportusa@crane-electronics.com
serviceusa@crane-electronics.com
www.crane-electronics.com

Crane Electronics Ltd – if you are based in the UK, Europe, Asia, Africa, or Middle East

Watling Drive Sketchley Meadows Hinckley LE10 3EY United Kingdom
+44 (0)1455 25 14 88
 sales@crane-electronics.com
support@crane-electronics.com
service@crane-electronics.com
www.crane-electronics.com

Crane Electronics GmbH – if you are based in Germany, Austria and Switzerland (German speaking)
Im Rank 5 73655 Plüderhausen Germany
+49 (0) 7181 9884-0
salesDE@crane-electronics.com
supportDE@crane-electronics.com
serviceDE@crane-electronics.com
www.crane-electronics.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals